Xycom XVME-212 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 67

background image

XVME-212 Manual
August, 1989

Chapter 1

INTRODUCTION

1.1 INTRODUCTION

The XVME-212 is a 32 channel, opto-isolated, digital input interface, designed to be

compatible with the VMEbus structure. The XVME-212 is capable of receiving 32 digital

inputs at frequencies up to 3.4 KHz. To ensure signal integrity, the design incorporates
integrated “switch” debouncing, as well as the protection provided by the optical isolation
of the channel inputs from the system bus structure. In addition, an on-board scanner can

be programmed to generate a VMEbus interrupt when any input changes state, thus
eliminating the need to poll the input module.

Each digital input is reverse voltage protected and is capable of handling a maximum

reverse bias of 50V DC (XVME-212/l) or 6.5V DC (XVME-212/2). Also, the board can be
jumpered to occupy any 1K block within the short I/O address space.

The following two versions of the XVME-212 are available:

XVME-212/l

-- The /l version of the XVME-212 comes with an on-board, 12V DC,

isolated power supply. The 12V supply is factory-connected to the input of each channel,

thus permitting the system to monitor 12V relay contacts and switches without an external
power supply. Voltages other than the 12V may be applied to the inputs (within the l0V-

50V input range); however, some board modification will be necessary (i.e., cutting the
well identified and easily accessible PC traces to the 12V on-board supply).

XVME-212/2

-- The /2 version of the XVME-212 is very similar to the /I version except

for the range of allowable input voltage and the absence of an on-board +12V DC power
supply. The XVME-212/2 has TTL level inputs with a 6.5V maximum input. In addition,

the +12V isolated, on-board power supply is not available, replaced by wire jumpers to
the existing +5V supply of the VME backplane.

1.2 MANUAL STRUCTURE

This first chapter provides a functional overview of the XVME-212 and presents the
features of Xycom’s Standard I/O architecture. Operational aspects of the XVME-212 are

then explained in the following fashion:

Chapter 2 -

Installation:

Information required to position the jumpers and switches

on the XVME-212, and install the module in a VMEbus chassis.

Chapter 3 -

Programming:

Information required to program the XVME-212 and

read digital input signals.

The appendices at the end of this manual provide information on Xycom’s Standard I/O
Architecture, VMEbus connector/pin descriptions, module schematics, as well as a quick

reference guide to the module’s jumpers and registers.

1-l

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
5
6
7
8
9
...
»

Содержание XVME-212




































































Отзывы:

Нет отзывов

Похожие инструкции для XVME-212

Бренд: Gantner Страницы: 56

Бренд: JDS Uniphase Страницы: 27

Бренд: Danfoss Страницы: 20

Бренд: OEG Страницы: 168

Бренд: C3 Custom Coolers Страницы: 16

Бренд: CALEFFI Страницы: 12

QuickSetter+ 132 Series

Бренд: CALEFFI Страницы: 5

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 60

Бренд: Danfoss Страницы: 20

Бренд: Saftronics Страницы: 13

Бренд: WAREMA Страницы: 4

SMARTSTART 6000

Бренд: Zener Страницы: 36

Бренд: Zapi Страницы: 5

Бренд: PUTCO Страницы: 2

Бренд: D+H Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды