background image

1. DESCRIPTION

2. SPECIFICATIONS

3

www.xprgroup.com

22

BIOPROX-MF is a Wiegand biometric and proximity reader for access control applications with programmable 
wiegand output. It offers storage of up to 9500 fingerprints, it reads 

 

Mifare Classic 1K & 4K, Ultralight, Desfire

cards/tags and has a programmable Wiegand Output (8 to 128 bits).
The tamper switch output can trigger the alarm system, if an attempt is made to open or remove the unit from 
the wall.

www.xprgroup.com

11. SAFETY PRECAUTIONS

Do not install the device in a place subject to direct sun light without protective cover.
Do not install the device and cabling close to a source of strong electro-magnetic fields like radio-transmitting antenna.
Do not place the device near or above heating equipments.
If cleaning, do not spray or splash water or other cleaning liquids but wipe it out with smooth cloth or towel.
Do not let children touch the device without supervision.
Note that if the sensor is cleaned by detergent, benzene or thinner, the surface will be damaged and the fingerprint can't 
be entered.

12. TROUBLESHOOTING

Enrollment from desktop reader can be done, but the
Fingerprints are not sent to all Biometric Readers
in the network

·Check the Ser.No of the Readers. 
·Check if proper termination is done as described before
Check if the Communication wires (A & B) are properly 
connected to the reader

The Biometric Reader is not powered ON.
The tricolour LED is OFF.

Check the power Supply (red & black wire)

Fingerprint (or Card) is recognized (the tricolor LED is 
green), but the controller reports other ID number and 
the access is denied

·If the user is not deleted from the reader and the same 

user is enrolled again with new ID, the reader will 
recognize the finger with the first ID. To resolve this, 
delete all users from the reader and upload all users to 
the reader

·Check the Wiegand Bus (yellow & white wire)
·Check if the ground of the controller and the Biometric 

Reader is the same

Check if the length between Biometric Reader and the 
controller is less than 50 m

Electro static discharge influences the Fingerprint
Scan.

Connect the housing of the Biometric Reader to the 
earth wire

Reader reading performance is decreased

·

Check if fingerprint reading area is dirty. Do not clean 

the device with any form of liquid. Use soft and dry 
cloth only

Reading area is damaged. If the damage is minor, try to 
calibrate the sensor

Fingerprint is not recognized normally

·Retry after drying the wetness of your finger
·When your finger is too dry, touch your forehead and 

try again

When you have a cut on your registered finger, register 
another fingerprint

The Proximity of the Biometric Reader is not working

The operation Mode of the Biometric Reader is set as 
“Finger”. Please select “Card OR Finger” mode

Tags are working correctly, finger scan does not work. 

·Fingerprint Sensor malfunction
·Check the Sensor position and its physical condition
Reset the system. Contact your installer

Technology

Authentication

Interface

Protocol programming

Fingerprint Sensor Type

 1:1000 identification 

Fingerprint enrolment

Panel Connection

Green and Red LED

Buzzer

Consumption

Power supply

IP Rating

Operating Temperature

Dimensions (mm)

Biometry and Mifare (13,56Mz)

Finger, Card, Finger or/and Card, Finger on Card

Wiegand 8 to 128 bits; Default: Wiegand 26bit

By PROS software (EWS system) and BIOMANAGER (all access control systems)

Capacitive

970 msec,  including feature extraction time

On the reader or from the USB desktop reader (BIOE)

Cable, 1m

Externally Controlled

Yes

Max. 200mA

65

9-14V DC

-15°C to +50°C

100 x 94 x 30

Housing

Colour

ABS

Silver, Red, Green, Dark Grey, Blue, White

Cable distance

50m

Backlight ON/OFF

Yes, by software settings

Fingerprint capacity

up to 9500 fingerprints; unlimited in Finger on Card mode

Fingerprints per user

1-10 fingerprints

Tamper

Yes

Proximity reading type

Mifare Classic 1K & 4K, Ultralight, Desfire; Finger on Card (Classic and Desfire)

Reading distance

1.5 to 5.5cm

Содержание BIOPROX-MF













Отзывы: