Xo FLEX Скачать руководство пользователя страница 4

Страница: 4 / 59

XO FLEX – Installation instructions

Table of contents

5.10 Installation of Dürr intra oral camera .................................................................................... 40

5.11 Finalizing installation of the instrument bridge ..................................................................... 40

5.12 Connecting water, compressed air, suction/drain and power supply .................................. 40

5.13 Connecting 230 V and the suction motor ............................................................................ 41

Connecting Mains supply cable .................................................................................... 41

Connecting suction motor control cable ....................................................................... 42

5.14 Fitting the patient chair ........................................................................................................ 42

5.15 Finalizing the installation ..................................................................................................... 44

Attach the patient chair seat upholstery ....................................................................... 44

Fit the cuspidor bowl and cup holder ........................................................................... 44

Fit XO Water disinfection and XO Suction disinfection cartridges ................................. 44

5.16 Connection of external equipment ...................................................................................... 45

6 Checking the unit ......................................................................................................................... 46

Adjustment of the instrument balance suspension ......................................................... 46

6.2 Start and check the unit ........................................................................................................ 47

6.3 Finalizing the installation ....................................................................................................... 48

6.4 Adjusting the unit .................................................................................................................. 48

Adjusting the air instrument (turbine), drive air and cooling air of the micromotor .......... 48

Adjusting the balance spring and friction brake in the bridge forearm ............................ 50

Adjusting the pivoting jonts of the bridge arm ................................................................ 51

Adjustment of the friction brakes in the operating light arm and display arm.................. 52

Adjusting the cuspidor and cup filler ............................................................................... 53

7 Handing the unit over to the users ............................................................................................... 55

8 Symbols ....................................................................................................................................... 56

Содержание FLEX




























































Результаты поиска

Содержание FLEX

Отзывы:

Похожие инструкции для FLEX

Бренды по названию

Популярные бренды

Xo FLEX, Руководство по установке

Результаты поиска

Содержание FLEX

Отзывы:

Похожие инструкции для FLEX

Бренды по названию

Популярные бренды