Xo FLEX Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 59

background image

XO FLEX – Installation instructions

Transportation

and unpacking

12

4

TRANSPORTATION AND UNPACKING

4.1

TRANSPORT

Upon arrival, check that no boxes suffered transportation damage.
Any signs of damage must be noted on the shipping documents and the transport
company / forwarding agent must be contacted.

If the “shock indicator” attached to the patient chair box has turned red – please
unpack the chair immediately and check that the chair did not suffer any damage!

4.2

UNPACKING

XO FLEX is delivered on two pallets, containing 4–8 boxes, depending on the configuration.

Figure 2 – XO FLEX packed in boxes

The boxes contain the following:

A.

Unit stand, including foot control, installation kit, panels, instructions for use and
accessories

B.

Unit mounting plate

C.

HD display

D.

Operating light

E.

XO Stool / XO Seat

F.

Instrument bridge and suction hoses

G.

Patient chair with upholstery

«
...
10
11
12
13
14
...
»

Содержание FLEX




























































Отзывы:

Нет отзывов

Похожие инструкции для FLEX

Бренд: MacDon Страницы: 84

Бренд: MacDon Страницы: 89

Бренд: Patton electronics Страницы: 18

Бренд: 3M Страницы: 2

Бренд: parr Страницы: 20

Бренд: Landoll Страницы: 71

Бренд: York Fitness Страницы: 4

Бренд: W&H Страницы: 23

Бренд: Bartscher Страницы: 24

Бренд: NEC Страницы: 44

Movie FL Black E27 Flaps

Бренд: Qazqa Страницы: 2

Бренд: Nektar Страницы: 3

Бренд: Youkey Страницы: 86

Бренд: Wacker Neuson Страницы: 62

Бренд: IDEAL Networks Страницы: 10

Бренд: Ultrasonic Страницы: 33

Бренд: Tarmo Страницы: 4

INTEGRA ARINC e-NAV

Бренд: Kannad Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды