Xo FLEX Скачать руководство пользователя страница 49

Страница: 49 / 59

XO FLEX – Installation instructions

Checking

the unit

Check/adjust drive air pressure

Action

Display

Activate

►

(Figure 67)

Actual value (0–100)

Adjustment of maximum drive
air to 3.2 bar.

Activate

🠪🠪

to increase pressure.

Activate

⬅

to decrease pressure.

Actual value (0–100)

Activate

◄

to save value.

DA MAX shown

Check the minimum drive air
pressure.

Activate

🠫🠫

DA MIN

Activate

►

Actual value (0–100)

Adjust to 1.5 bar.

Activate

🠪🠪

to increase pressure.

Activate

⬅

to decrease pressure.

Actual value (0–100)

Activate

◄

to save value.

DA MIN shown

Check A/R Air (Anti-Retraction
Air).

Activate

🠫🠫

A/R AIR

Activate

►

Actual value (0–100)

Adjust to have very small
amount of airflow

without

the

turbine burr spinning.

Activate

🠪🠪

to increase pressure.

Activate

⬅

to decrease pressure.

Actual value (0–100)

Activate

◄

to save value.

A/R AIR shown

Place the air instrument on the
instrument bridge again.

Figure 66 – Configuration button

Figure 67 – Foot control

Table 5 – Adjustment of micromotor cooling air

Содержание FLEX




























































Результаты поиска

Содержание FLEX

Отзывы:

Похожие инструкции для FLEX

Бренды по названию

Популярные бренды

Xo FLEX, Руководство по установке

Результаты поиска

Содержание FLEX

Отзывы:

Похожие инструкции для FLEX

Бренды по названию

Популярные бренды