Xerox Troy PocketPro 100 Скачать руководство пользователя | Manualshive

Страница: 9 / 158

background image

Operator Guide

vii

Safety

Please contact your Xerox representative for more information.

Warning markings

All warning instructions marked on or supplied with the product
should be followed.

This WARNING alerts users to areas of the product where there is
the possibility of personal damage.

This WARNING alerts users to areas of the product where there
are heated surfaces, which should not be touched.

Electrical supply

This product shall be operated from the type of electrical supply
indicated on the product’s data plate label. If you are not sure that
your electrical supply meets the requirements, please consult your
local power company for advice.

This product must be connected to a protective earth circuit. This
product is supplied with a plug that has a protective earth pin. This
plug will fit only into an earthed electrical outlet. This is a safety
feature. Always connect equipment to a properly grounded
electrical outlet. If in doubt, have the outlet checked by a qualified
electrician.

To disconnect all electrical power to the product, the disconnect
device is the power cord. Remove the plug from the electrical
outlet.

Ventilation

Slots and opening in the enclosure of the product are provided for
ventilation. Do not block or cover the ventilation vents, as this
could result in the product overheating.

This product should not be placed in a built-in installation unless
proper ventilation is provided, please contact your Xerox
representative for advice.

WARNING

«
...
7
8
9
10
11
...
»

Содержание Troy PocketPro 100































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Troy PocketPro 100

Бренд: IBM Страницы: 112

Бренд: Canon Страницы: 58

image Prograf iPF680 Series

Бренд: Canon Страницы: 132

Бренд: Canon Страницы: 44

imageClass LBP6230dw

Бренд: Canon Страницы: 16

Бренд: Canon Страницы: 2

imageprograf IPF785

Бренд: Canon Страницы: 42

Бренд: Canon Страницы: 148

Color Bubble Jet BJC-8200

Бренд: Canon Страницы: 6

Color Bubble Jet BJC-1000 Series

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

Color Bubble Jet BJC-8200

Бренд: Canon Страницы: 105

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 68

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды