Xerox Troy PocketPro 100 Скачать руководство пользователя

Страница: 110 / 158

5 - 8

Operator Guide

Troubleshooting

made to change the orientation using the Xerox Client
Software print command orientation switch, <orientation>?

Additional TIFF questions:

•

What compression format was used to compress the file (for
example: group 3, group 4, packbits, or RLE)?

•

What dots per inch (DPI) resolution was used or intended for
the file (for example: 300 dpi or 600 dpi)?

•

What TIFF specification was used or intended for the file (for
example: TIFF Spec. 5.0 vs. TIFF Spec. 6.0)?

•

Did this file or similar files print on a previously installed
version of the system software?

•

Has printing been attempted with the most recent version of
system software installed?

Isolating PDF file problems

Ask the following questions when there are problems with PDF
files:

•

Did you try creating the PDF from the original PostScript
through the latest version of Adobe’s PDF Distiller?

•

Does the original PostScript file print correctly? If yes, does it
print correctly on other PostScript printers?

•

Can you open all pages within Adobe’s Acrobat? Within
Acrobat, can you print correctly from PostScript?

•

What application and/or PDF software created the PDF file?

•

With the printer’s error pages turned on, does the printer
produce a PostScript error page?

•

Does the PDF file print on other PDF printers?

•

Have you tried printing the PDF file using the most Current
release of system software?

•

Have you tried redistilling the PostScript file again?

•

Have all the document fonts been downloaded and included
throughout the process? Keep in mind that the fonts have to
be within the PostScript and the resulting PDF.

•

Did you use PDF Writer to create the PDF file? If so, recreate
the PDF file using Adobe’s PDF Distiller.

Troubleshooting process problems

Process problems mean that a procedure is followed incorrectly or
performed by mistake.

•

Problem: [Exit] was selected from the System menu in error.

To start the DocuSP software without rebooting the controller:

Содержание Troy PocketPro 100































































































































































Результаты поиска

Содержание Troy PocketPro 100

Отзывы:

Похожие инструкции для Troy PocketPro 100

Бренды по названию

Популярные бренды

Xerox Troy PocketPro 100, Руководство оператора

Результаты поиска

Содержание Troy PocketPro 100

Отзывы:

Похожие инструкции для Troy PocketPro 100

Бренды по названию

Популярные бренды