Xerox Troy PocketPro 100 Скачать руководство пользователя

Страница: 26 / 158

1 - 1 0

Operator Guide

Overview

Printer components

The components and special features of the Xerox DocuPrint 100/
115/135/155/180 EPS printer are shown in the following figure.

Figure 1-4 Printer components

1. Processor feeder trays
2. Sample tray
3. Attention light
4. Purge tray
5. Feeder/stacker module
6. Inverter feeder/stacker

NOTE: Some printer configurations may include a control console
(not shown).

Processor Feeder Trays

Two processor feeder trays (trays 1 and 2) are located in the main
part of the printer and are not part of a feeder/stacker module.

Trays 1 and 2 can handle paper sized from 8 by 10 inches / 203 by
254 mm to 9.02 by 14.02 inches / 230 by 356 mm.

Sample tray

The sample tray, located on top of the printer, receives output
such as transparencies, sample sheets from printing jobs, prints
from system files such as forms, and waste sheets that cannot be
sent to the purge tray.

Monitor the sample tray and empty it when it contains 100 sheets.

NOTE: The system does not notify you when the tray is full.

Содержание Troy PocketPro 100































































































































































Результаты поиска

Содержание Troy PocketPro 100

Отзывы:

Похожие инструкции для Troy PocketPro 100

Бренды по названию

Популярные бренды

Xerox Troy PocketPro 100, Руководство оператора

Результаты поиска

Содержание Troy PocketPro 100

Отзывы:

Похожие инструкции для Troy PocketPro 100

Бренды по названию

Популярные бренды