Xerox Troy PocketPro 100 Скачать руководство пользователя | Manualshive

Страница: 42 / 158

background image

1 - 2 6

Operator Guide

Overview

functions such as requesting sample prints, or shutting down the
system.

Mouse

The mouse is another main method of communicating with the
printer.

Display monitor

The LCD monitor allows you to interact with the printer and to
monitor its interaction with the various components. During a print
job, printer error messages may display to notify you of any
unexpected conditions.

Optional processor

components

The controller may be configured with any of the following optional
components:

•

Connectivity board to enable Token Ring

•

Channel interface board for channel connection to a host for
online LCDS printing

•

One SCSI board to connect to an external tape drive

•

Creator-3D series 3 graphics board (may replace the video
graphics board delivered with the controller)

External components and options

The following components are external to the processor. The
controller stand contains sections that may hold these
components.

•

Quarter-inch cartridge (QIC) tape drive

•

36-track cartridge tape drive (optional)

•

External 36 GB hard disk drive (optional)

NOTE: This additional drive is standard equipment on systems
with the NPS/IPS extension.

Controller stand

The controller is provided with a special stand that holds all its
standard components. In addition to the processor, keyboard with
the mouse, and the quarter-inch cartridge tape drive, the stand
can accommodate the optional 36-track tape drive and one
external hard disk drive (required for the NPS/IPS Extension
option).

Online and offline interfaces

The Xerox DocuPrint 100/115/135/155/180 EPS may be
configured for either the online interface, the offline interface, or
both.

Online interface

The online (channel-attached) interface receives input directly
from any environment that supports the IBM 3211 and 4245 host
systems.

«
...
40
41
42
43
44
...
»

Содержание Troy PocketPro 100































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Troy PocketPro 100

Sure shot 80 tele

Бренд: Canon Страницы: 24

iPF720 - imagePROGRAF Color Inkjet Printer

Бренд: Canon Страницы: 8

Бренд: Canon Страницы: 2

Бренд: DataCard Страницы: 17

Бренд: DataCard Страницы: 24

DocuPrint C3055 DX

Бренд: Xerox Страницы: 20

DocuPrint 4850 NPS

Бренд: Xerox Страницы: 276

Donation Point Even

Бренд: Quest Payment Systems Страницы: 2

Бренд: IDStation Страницы: 18

Бренд: Xerox Страницы: 13

Бренд: Creality Страницы: 24

Бренд: Citizen Страницы: 32

Бренд: Konica Minolta Страницы: 12

EuroLine Series

Бренд: Output Technology Страницы: 73

WorkCentre 6655i

Бренд: Xerox Страницы: 282

Бренд: Pantum Страницы: 164

Бренд: BIG TREE TECH Страницы: 11

Бренд: Citizen Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды