manualshive.com logo in svg

Xerox Synergix 8850, Руководство по обслуживанию

Операторская инструкция Xerox Synergix 8850 - важное руководство для правильной работы устройства. Здесь вы найдете все необходимые сведения для эффективного использования вашего принтера. Скачайте эту инструкцию бесплатно на manualshive.com, чтобы получить доступ к полезной информации.

Поделиться
Скачать
background image

03/2003 

1-13

8850/ 510DP 

Maintenance Procedures

Service Call Procedures

Maintenance Procedures

Table 1 Image Module

INTERVAL

TASK

REASON

TASK ENABLER

Normal Call

Check, clean, or repair spacing wheels
as required.

Contaminated, dirty or worn spacing wheels or Drum
ends cause print quality defects.

Clean or replace spacing wheels and the end surface of the Drum that the 
wheels ride on.

Normal 

Call

Check and clean, if required, the
charge Scorotron.

Contaminated grid, bent or contaminated pins. Worn
end blocks, are also causes for scorotron failure,
which results in print quality defects.

WARNING

The scorotron pin arrays are very sharp. Use care when handling the 
assembly.

If contaminated, remove scorotron assembly and clean both sides of the 
grid with a brush. Examine pins and clean with brush Only if contaminated. 
Cleaning with a cloth can deposit lint that will cause print quality problems.

Normal Call

Clean the image bar.

Contamination causes print quality defects.

Clean the image bar with a lint free cloth and lens cleaner.

15K ft.
4.5Km

Clean the Scorotron Screen.

Contamination on the screen causes print quality 
defects

Remove the Scorotron Screen and clean it with a brush. 

NOTE: Do not use a cloth to clean the Scorotron Screen as it can leave lint 
on the screen, causing print quality problems.

As Required

Repair or replace the scorotron/ grid.

Contamination causes print quality defects.

WARNING

The scorotron pin arrays are very sharp. Use care when handling the 
assembly.

Replace the grid and/or pin array.
Perform 

ADJ 9.2

 Electrostatic Series.

Table 2  Drum/ Cleaner Module

INTERVAL

TASK

REASON

TASK ENABLER

Normal Call

Clean the Drum/cleaner module.
Clean the Erase Bar.
Inspect the Drum for damage.
Inspect components for vellum con-
tamination.
Inspect all seals for damage.
Inspect the Cleaner Blade for damage.

Contamination can cause print quality problems. Con-
taminants can travel to the LED bar and scorotrons,
which results in print quality problems. Fused toner on
the bottom of the module can cause jams.
Contamination reduces the effectiveness of the lamp
to discharge the Drum.
Contaminants from vellum
- Cleaner failure
- Contaminants to prints.
Vellum contamination will contaminate and plug the
cleaner auger at the ends.

Clean the toner from the housing and cleaner blade with a vacuum cleaner.

NOTE: Ensure that the vacuum cleaner does not contact the edge of the 
cleaner blade that touches the surface of the Drum.

Perform the Drum Cleaning Enhancement procedure in section 6. Use 
cleaning solvent to remove any fused toner from the bottom of the module. 
Replace the Drum if damaged.
Clean the Erase Bar with a brush or dry lint free cloth.
Replace any damaged xerographic module seals.

As Required

Check/clean the Drum.

Contamination/wear, scratches, or chips can generate
print quality problems.

Inspect Drum surface for deep scratches, chips or excessive wear. Replace 
Drum if damaged.
Apply zinc stearate to the cleaning blade and Drum. *Note 2
Clean Drum surface with Xerox Film Remover if contaminated. Apply zinc 
stearate when surface is dry.

As Required

*Note 3

Check/clean the cleaning blade.
Replace with the new Drum or as
required.

Residual image, streaks, Drum scuffing can occur if
the blade is worn or contaminated.

Vacuum clean the cleaning blade. *Note 1
Apply zinc stearate to the cleaning blade and Drum. *Note 2
Replace the blade if damaged.

Содержание Synergix 8850

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Synergix 8850

Canon DADF-M1 General Timing Chart/General Circuit Diagram preview
DADF-M1
Бренд: Canon Страницы: 16
Canon IR5000 - iR B/W Laser Driver Manual preview
IR5000 - iR B/W Laser
Бренд: Canon Страницы: 86
Canon AE-1 Installation Procedures Manual preview
AE-1
Бренд: Canon Страницы: 48
Samsung CLP 510N - Color Laser Printer Manual Del Usuario preview
CLP 510N - Color Laser Printer
Бренд: Samsung Страницы: 270
Samsung Bixolon SRP-270 Integrator'S Manual preview
Bixolon SRP-270
Бренд: Samsung Страницы: 13
Tally T6090 Maintenace Manual preview
T6090
Бренд: Tally Страницы: 202
Raymarine e7 Installation And Operation Handbook preview
e7
Бренд: Raymarine Страницы: 135
Canon RP10 User Manual preview
RP10
Бренд: Canon Страницы: 37
Samsung CLP-775ND Service Manual preview
CLP-775ND
Бренд: Samsung Страницы: 134
Xerox Phaser 6300 Service Manual preview
Phaser 6300
Бренд: Xerox Страницы: 13
Konica Minolta bizhub C258 Quick Start Manual preview
bizhub C258
Бренд: Konica Minolta Страницы: 266
Ricoh SP C250SF Settings Manual preview
SP C250SF
Бренд: Ricoh Страницы: 4
Oce cm2522 User Manual preview
cm2522
Бренд: Oce Страницы: 222
Oki MB451wMFP User Manual preview
MB451wMFP
Бренд: Oki Страницы: 198
SEWOO LK-T200 User Manual preview
LK-T200
Бренд: SEWOO Страницы: 13
Buffalo LPV4-U2-300S Quick Setup Manual preview
LPV4-U2-300S
Бренд: Buffalo Страницы: 2
Konica Minolta IC-206 User Manual preview
IC-206
Бренд: Konica Minolta Страницы: 424
MIMAKI UJF-605R II Daily Care Manual preview
UJF-605R II
Бренд: MIMAKI Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды