manualshive.com logo in svg

Xerox Synergix 8850, Руководство по обслуживанию

Поделиться
Скачать
Xerox Synergix 8850 Скачать руководство пользователя страница 294

03/2003 

6-8

8850/ 510DP

Special Tests

General Procedures

[0360]

NVM Reset to Default.
Entering the number 1 or 3 resets all 
the NVM values to the default val-
ues.
Entering the number 2 allows the 
electronic billing to be reset to any 
desired value.

1 = NACO NVM Default
2 = Billing
3 = EO NVM Defaults

NOTE: If the web oiler is not new, run 
[1031] to set the counter value to reflect 
the remaining length.

[0361]

Watchdog Timer Test.
This code can be used to exit the 
Diagnostic mode

[0362]

Diagnostic Time-out interval. This 
code allows the adjustment of the 
time interval that the Printer will stay 
in the Diagnostic mode.

0-50 minutes

[0363]

NVM Reset
This code allows the NVM values to 
be reset to the previously adjusted 
values. The software compares the 
NVM values to a backup file and will 
reset the values that are not the 
same as the values in the backup 
file.

[0364]

Reset NVM Check Sum

[0365]

NVM Printout of NVM contents in 
hex format.

[0366]

NVM Dump of Adjustable Settings. 
NOTE:  This information is accessi-
ble through the Printer Main PWB, 
J611.  

Refer to 

GP 7

, NVM Dump of Adjust-

able Settings, later in this section.

[0391]

Recent Fault Log
Displays the last 99 faults that have 
occurred.  

Displays the fault code, how many 
events ago it occurred, and the billing 
meter reading at the time the fault was 
originally displayed. Log entries are 
numbered from 1 to 99, with 1 being the 
most recent.

[0392]

Fault History Log

Displays, in alphabetical order, the 
number of occurrences of each of the 
fault codes since the log was last 
cleared.

[0602]

Vertical Magnification
Go to 

ADJ 8.1

 Vertical Magnification 

Adjustment

0-40mm

[0700]

Cut Length Adjustment
Go to 

ADJ 8.3

 Cut Length.

600mm is ###mm

[0750]

Adjust Heater on RH setpoint. 

0-99 RH

Table 1 Special Tests

Code

Description

Value

[0760]

Delay Between Prints (Film)  
Increases the time delay between 
making prints on Film Media

1-30 Secs

[0809]

Enable/Disable Stack Height Sensor 00# 00#

[0860]

Image Registration
Go to 

ADJ 8.2

 Lead Edge Registra-

tion.

0-40mm

[0904]

Automatic ESV Setup.

Sequentially steps through test,
displays values when complete.

[0906]

Tone Up/Tone Down (Automatically 
adjusts toner concentration until the 
control set point is reached).

Desired sensor voltage = #.# volts
Actual sensor voltage = #.# volts

[0907]

Current Dispense Mode.

TDK or Sleep

[0920]

Displays Run Time.

#.# Hours

[0921]

Electrostatic Setup
This code is used adjust the electro-
statics.  When in this code, specific 
tests can be run by pressing the fol-
lowing buttons:
1 AC/Transfer on Xerographic HVPS
2 Clean Voltage Measurement
3 Adjust Vlow (obsoleted by [0904])
4 Adjust Image Density (

ADJ 9.3

), 

Toner Sensor Vbias
5 LED Image Bar Illumination Test.
6 Calibrates the Toner Control Sen-
sor.
7 Humidity Sensor control point set-
ting.

Xerographic High Voltage Power Sup-
ply On
060-175
0-20
0-6.0

Observe Bar
IOT reveals

>65% RH
1=yes, 2=no

[0922]

This code disables toner faults so 
that the Printer will continue to oper-
ate.

[Yes]

 for running with toner faults.

[0926]

Resets the Toner Control Bias to 
default value

#.# volts

[0955]

IOT Internal Test Pattern Print

test patterns: 1-9
roll select: 1-3
length of print: 210-50000mm
quantity of prints: 1-255

[0970]

Adjust test patterns for code [0921-
5]. Use two different pattern numbers 
to see the LED bar change in code 
[0921-5]. 

1-9

Table 1 Special Tests

Code

Description

Value

Содержание Synergix 8850

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды