manualshive.com logo in svg

Xerox Synergix 8850, Руководство по обслуживанию, Страница: 307 / 432

Поделиться
Скачать
Xerox Synergix 8850 Скачать руководство пользователя страница 307

03/2003 

6-21

8850/ 510DP 

Installation Procedure

General Procedures

Installation Procedure

NOTE: 

Except where specified, the install procedure  is common to both the 8850 and the

510dp Printers. Photographs and illustration are mainly of the 8850.

Power Requirements for the Printer

CAUTION

Before installing the Printer, check for the correct voltage, polarity, and the grounding of the AC
outlet that is provided by the customer. Use the Digital Multimeter. Incorrect voltage applied to
the Printer could result in poor performance or damage to the Printer.

NOTE: The power line outlet must be a dedicated line (wired directly to the circuit breaker
panel), with the correct current rating (ampheres) as indicated in (

ADJ 3.2

) Line Current, with

no shared neutral, and a different phase from the lighting circuits.

CAUTION

If the supply AC voltage specifications are not met, the AC outlet may be wired or grounded
incorrectly.  Inform the customer and request that a licensed electrician correct the problem.
DO NOT attempt to make the correction yourself.

NOTE: The Power Cord is the disconnect device for this equipment.  Ensure that the installa-
tion is near the outlet and is easily accessible.

•

(

Figure 1

): Check for 220 AC input voltage at the wall outlet:

–

Check for 208 - 240 VAC between the AC Hot (ACH) terminals.

Check for 110 - 120 VAC between each AC Hot (ACH) terminal and Ground.

NOTE: 110 VAC input voltage can only be used when the customer’s copy speed require-
ments are 5 or 7 D(A1)-size per minute. If 10 D (A1)-size per minute is required, 220 VAC
must be used.

Check for 110 VAC input voltage at the wall outlet:

–

Check for 105-125 VAC between AC Hot and AC neutral.

Check  for 105-125 between AC Hot and AC ground

Check for less than 2 VAC between AC neutral and ground.

Figure 1 Checking the Ground and AC voltages

Floor Space Requirements

WARNING

This product will produce ozone during operation. The ozone that is produced is depen-
dent on the print volume and is heavier than air. Providing the correct environmental
parameters as specified in Xerox installation procedures will ensure that concentration
levels meet safe limits

•

The minimum space requirement is 116.75 inches (292 cm) x 85 inches (212.5 cm).

USO Only

:  If additional information concerning ozone is needed, request the Xerox publica-

tion  

600P83222

, Ozone by calling 1-800-828-6571.

Hot (ACH) 
Red or 
Black Wire

Ground 
Green Wire

220 VAC

  

20 AMP

10 D (A1)-D size prints 
per minute

NEMA =5 - 20R 

Hot (ACH) 
Red or 
Black Wire

USO ONLY 

Ground 
Green Wire

NEMA = 6 - 20R 

Hot (ACH) 
 Black Wire

Neutral (ACN) 
White  Wire

20 AMP 

115 VAC

 

 20AMP

(5 or 7 D (A1)-size prints 
per minute only)

Содержание Synergix 8850

















































































































































































































































































































































































































































Отзывы:

Нет отзывов