manualshive.com logo in svg

Xerox Synergix 8850, Руководство по обслуживанию

Поделиться
Скачать
Xerox Synergix 8850 Скачать руководство пользователя страница 51

03/2003 

2-17

8850/ 510DP 

OF-1 Control Panel RAP, OF-2 Power On Self Test

Status Indicator RAPs

OF-1 Control Panel RAP

NOTE: Go to  BSD 2.1 while using this RAP, unless otherwise directed.

This RAP is used when the Control Panel does not operate, or when the Control Panel oper-
ates incorrectly.

Initial Actions

•

Make sure that AC power is applied to the machine.

•

Check that the DC voltage LEDs are lit on the Main PWB (A3).

•

Ensure that the 26-conductor ribbon cable, connected between the Main PWB A3J301
and the User Interface PWB A32J1 (located in the Control Panel), is seated fully at each
connector.

Procedure

OF-2 Power On Self Test (POST) RAP

NOTE: Go to  BSD 1.2 and  BSD 2.1 while using this RAP.

This RAP is used when the logic detects a fault during the Power On Self-test (POST). The
printer does not initialize and the Control Panel displays a  

1

,  

2

,  

3

,  

5

,  

6

, or  

7

.

Initial Actions

•

Ensure that the  NVRAM are seated fully on the Main PWB, A3.

•

Ensure that the 26-conductor ribbon cable, connected between the Main PWB A3J600
and the Control Panel User Interface PWB A32J1, is seated fully at each connector.

Procedure

Table 1 Control Panel Probable Cause / Corrective Action

Control Panel

Probable Cause

Corrective Action

The Message Display is 
blank, no characters are 
displayed.

There is an input power
problem.

There is an open circuit in
the ribbon cable between
the Main PWB A3J301 and
the User Interface PWB
A32J1.
There is an internal fault in
the Control Panel or in the
Main PWB A3.

Go to 

1.1 AC Power RAP

 and 

1.2 

DC Power RAP

.

Check for continuity in all wires in 
the ribbon cable.
Replace the Control Panel, 

PL 1.4

. If 

the problem persists, replace the 
Main PWB, A3, 

PL 1.1

.

The Message Display 
LEDs are on but no char-
acters are displayed.

There is no +15 VDC to the
Main PWB, A3.
There is no +5 VDC (Bulk) to
the Main PWB, A3.

Go to 

BSD 1.2

 to troubleshoot the

+15 VDC power to the Main PWB,
A3.
Go to 

BSD 1.2

 to troubleshoot the

+5 VDC (Bulk) power to the Main
PWB, A3.

The Message Display 
LEDs are on but no char-
acters, random charac-
ters, or black squares 
appear.

There is an open circuit in
the ribbon cable between
the Main PWB A3J301 and
the User Interface PWB
A32J1.
There is an internal fault in
the Control Panel or in the
Main PWB A3.

Check for continuity in all wires in
the ribbon cable.
Replace the Control Panel, 

PL 1.4

. If

the problem persists, replace the
Main PWB, A3, 

PL 1.1

.

Table 1 Power On Self Test (POST) Probable Cause / Corrective Action

The number that is 

Displayed on the 

Control Panel.

Probable Cause

Corrective Action

1 or 2

There is a fault in the RAM 
memory.

Replace the Main PWB, A3, 

PL 1.1

.

3

The contents of the Control
EPROMs does not agree with
the checksum.
The Main PWB is defective.

Replace both Control EPROMs on
the Main PWB, A3.
Replace the Main PWB, A3, 

PL 1.1

.

5

There is a fault in the Main
PWB, A3.

Replace the Main PWB, A3, 

PL 1.1

.

6

There is a +5 VDC fault in the 
Digital-to-Analog Converter .

Replace the Driver PWB, A2,  PL 
1.1A.
If the problem persists, replace the 
Main PWB, A3, 

PL 1.1

.

7

There is a fault in the printer 
port output circuitry.

Replace the Main PWB, A3, 

PL 1.1

Содержание Synergix 8850

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды