manualshive.com logo in svg

Xerox Synergix 8850, Руководство по обслуживанию, Страница: 226 / 432

Поделиться
Скачать
Xerox Synergix 8850 Скачать руководство пользователя страница 226

03/2003 

4-150

8850/ 510DP

ADJ 9.3

Repairs and Adjustments

ADJ 9.3 Image Density

Purpose

The purpose is to set the toner concentration to maintain good print quality as specified in Sec-
tion 3 of this Service Manual.

Prerequisite

Perform the Electrostatic Series (

ADJ 9.2

).

Check

1.

Enter diagnostics.

2.

Enter [0907] and check if the Printer is in 

STANDARD

 or 

RECOVERY

 mode. If the Printer

is in 

RECOVERY

, run [0955-5] until Printer returns to 

STANDARD

.

3.

Enter code [

0955

] and make one print of Test Pattern #5.

4.

Using S.I.R. 495.01 (82P520), evaluate the darkness squares at the lower right center
and the upper left from the lead edge.

5.

If the darkness squares are not between 1.2 and 1.4, perform the adjustment.

Adjustment

1.

Enter diagnostics.

2.

(Figure 1): Enter code [

0921-4

]. The following message is displayed.

NOTE: RAW SENSOR X.X VOLTS is the sensor output voltage and VBIAS X.X VOLTS is
the sensor input voltage. These values will change as the CONTROL POINT voltage is
changed. The CONTROL POINT voltage has an inverse relationship to the image density.
As the CONTROL POINT voltage increases, the density and the RAW SENSOR voltage
decreases.

Figure 1 Adjusting the Image Density

a.

Use the 

Next

 key to increase the CONTROL POINT voltage which will decrease the

image density.

Use the 

Previous 

key to decrease the CONTROL POINT voltage which will

increase the image density.

b.

Make 20 D-size prints then perform the 

Check

 again. Then repeat Steps a and b

until the density is within specification

3.

To increase or decrease the density to meet customer requirements do the following:

Printer Offline > Printer Menu > Printer Adjustments > Density (Range 1-10)

 

Default

5

 and adjust the range higher to increase the density or lower the range to decrease the

density.     This will affect the density of the output plots in [

0955

]. This step can also be

done using the WebPMT with out affecting the output plots in [

0955

]. The adjustment will

be done in the AccXES Controller.

Содержание Synergix 8850

















































































































































































































































































































































































































































Отзывы:

Нет отзывов