manualshive.com logo in svg

Xerox Synergix 8850, Руководство по обслуживанию

Поделиться
Скачать
Xerox Synergix 8850 Скачать руководство пользователя страница 30

03/2003 

1-14

8850/ 510DP

Maintenance Procedures

Service Call Procedures

NOTE: 1. Ensure that the vacuum does not contact the edge of the cleaner blade that touches
the surface of the Drum.

NOTE: 2. Raise the Drum/Cleaning Module to dust the Drum and the cleaning blade with zinc
stearate to prevent the charge scorotron from being contaminated. Remove the Erase Bar to
prevent it from being contaminated. The zinc stearate may contaminate the charge scorotron
and Erase Bar and cause print quality defects.

NOTE: 3. Install the complete cleaning blade kit when installing a new Drum.

30K ft.

9Km

Clean the inner module components.

If the customer is running a high percentage of vellum,
outgassing of the vellum contaminates the cleaner
auger and lower baffle surface resulting in poor clean-
ing and high dirt contamination.
plugged cleaner auger

Remove the Drum to enable access.
NOTE: 

Use caution not to touch or damage cleaning blade or seals.

Vacuum the Module and Auger and then clean all contaminated areas with 
Film Remover.

Table 2  Drum/ Cleaner Module

Table 3 Fuser Module

INTERVAL

TASK

REASON

TASK ENABLER

Normal Call

Replace the Fuser Heat Roll at failure. Smooth or worn Fuser Heat Roll loses ability to drive

media.

Check/Adjust the Fuser Temperature (

ADJ 10.1

).

Normal Call

Check the Fuser Heat Roll for lack of
oil.

Too little oil can cause media handling and offsetting
print quality problems.

Check remaining fuser web life [1034] and adjust the Web Oiler rate [1032].
If the Fuser Heat Roll is dry, refer to 

BSD 10.2

.

Normal Call

Inspect/clean the thermistor pad

Contamination can cause fuser heat problems.

Clean the thermistor pad with a brush or dry lint free cloth.

Normal Call

Clean the under side of the Fuser Mod-
ule and Sheet Feed Pinch Rolls.

Reduce the airborne contaminants.

Wipe down with a lint free cloth and antistatic fluid.

Normal Call

Check and clean or replace the Strip-
per Fingers.
Clean the Media Guides.

Bent Stripper Fingers may cause feed out jams and
Fuser Heat Roll damage.
Contaminated or damaged media guides can cause
print quality defects.

Replace the damaged or contaminated Stripper Fingers.

Table 4 Media Transport and Lower Sheet Feed Assembly

INTERVAL

TASK

REASON

TASK ENABLER

Normal Call

Clean the lower paper transports, turn-
around baffle, Sheet Feed Rolls.

Contaminates can cause the media to slip resulting in
print quality defects.

Clean the transport with antistatic fluid and a lint free cloth.
Clean the Sheet Feed Roller with Formula A.

Normal Call

Vacuum clean the Bias Transfer Roll
(BTR).

Improve toner transfer to media.

Rotate the Bias Transfer Roll in place as you vacuum. Clean loose toner/
debris with a vacuum. Just lightly touch the BTR as you move the vacuum
tool over the roll, do not press the vacuum tool against the roll. This could
tear and damage the BTR.

125K ft.

42Km

 Replace the Bias Transfer Roll (BTR). Prevent print quality defects due to a worn roll.

Remove the Bias Transfer Roll.

Normal Call

Check / repair BTR spacing wheels as
required.

Contaminated, dirty or worn spacing wheels or Drum
ends cause print quality defects.

Clean the spacing wheels and the end surface of the Drum that the wheels 
ride on.

Normal Call

Check and clean or replace the Detack
Corotron Media Shields.

Contaminated or damaged Media Shields may cause
media jams.

Clean or replace the damaged or contaminated Media Shields. To clean the 
area of the Media Shields, hold a vacuum tool close to the Shields and 
brush any contaminates or toner loose for the vacuum to pick up. 
Check the stainless steel shield on the rear of the Detack aluminum chan-
nel for a white powder. If a powder is present, replace the stainless shields.

Содержание Synergix 8850

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды