manualshive.com logo in svg

Xerox Synergix 8850, Руководство по обслуживанию

Поделиться
Скачать
Xerox Synergix 8850 Скачать руководство пользователя страница 23

03/2003 

1-7

8850/ 510DP 

Status Code Entry Chart

Service Call Procedures

E4-01
No RAP

Fuser Exit Sensor error

The media trail edge jammed in the
Fuser Exit Sensor area.

•

Fuser Exit Sensor error
(S3)

•

Main PWB (A3)

•

Exit Rollers and Drive

•

Interference between
actuator and slot in
cover.

BSD 

10.3

PL
10.4
PL 1.1

E4-02
No RAP

Fuser Exit Sensor error

Lead edge of media did not reach
the Fuser Exit Sensor (S2) in the
allowed time period.

•

Fuser Exit Sensor (S2)

•

Fuser Heat Roll, Pres-
sure Roll, Vacuum and
Media Transport

•

Fuser Drive Motor

•

BTR/ Detack Corotron

BSD 

10.3

PL
10.4

E4-03
No RAP

Stripper Finger Jam Switch error

The Stripper Finger Jam Switch
(SW1) was actuated during the run
mode.

•

Stripper Finger Jam
switch (SW1), Fuser
Heat Roll, Pressure
Roll, 

•

Stripper Finger Dam-
aged, Web Oiler 

•

Worn Media Exit Drive
Rolls

BSD 

10.3

PL
10.4

E4-04
No RAP

Stacker Full

The Stack Height Sensor was actu-
ated during a run or was detected
to be actuated when the machine
powered

Stack Height Sensor

BSD 

10.3

PL
14.2

E4-09
No RAP

This is a Firmware problem

Press power off (0) then power on
(1). If problem persists, replace the
firmware.

E4-11
No RAP

Fuser Exit Sensor error

The Fuser Exit Sensor was
detected to be actuated when the
machine powered up. This requires
the Fuser exit area to be opened,
and the media to be removed.

•

Fuser Exit Sensor (S2)

•

Main PWB (A3)

BSD 

10.3

PL
10.4

E4-12
No RAP

Sheet Feed Sensor error

The Sheet Feed Sensor was
detected to be actuated when the
machine powered up. This requires
the Fuser exit area to be opened,
and the media to be removed.

•

Sheet Feed Sensor
(A21Q2) 

•

Main PWB (A3)

BSD 

8.1

PL
10.7
PL 1.1

Table 1 Status Code Entry Chart

Status
Code

Description

Components

BSD 

Ref

PL

Ref

E4-13
No RAP

Stripper Finger Jam Switch error

The Stripper Finger Jam Switch
was actuated at power on.

•

Stripper Finger Jam
Switch 

•

Main PWB (A3)

BSD 

10.3

PL
10.4
PL 1.1

E5-03
No RAP

Top Cover Interlock Switch error

The Top Cover was opened during
print.

•

Top Cover Interlock 
Switch (S26)

•

Main PWB (A3)

BSD 

1.3

PL
14.5
PL 1.1

E5-04
No RAP

Cutter Cover Interlock Switch
error

The Cutter was opened during
print.

•

Cutter Cover Interlock 
Switch (S1)

•

Main PWB (A3)

BSD 

1.3

PL 7.7
PL 1.1

E5-05
No RAP

Please Close the Fuser Exit Door.
The Fuser Drawer was opened 
while a print job was in progress.

Close the Fuser Drawer

BSD 
1.3

 

E5-06
No RAP

Front Door Interlock Switch
error

The front door was opened during
print.

•

Front Door Interlock
Switch (S21)

•

Main PWB (A3)

BSD 

1.3

PL
14.3

E7-01

Communication error

The IOT is unable to communicate
with the Controller. The IOT Off-
Line and Media menus will still
function, but cannot print from the
Controller or network.

Go to E701 RAP in Controller
Service Manual.

E7-02
No RAP

Printer message display error

A required message is not avail-
able. Download the language soft-
ware again.

Main PWB (A3)

PL 1.1

E9-XX

Software shutdown

This error is of unknown cause.
Escalate the service call.

Fx-xx

Refer to the Folder Service Man-
ual for all F-codes.

J1-01
No RAP

Toner Sensor error

Logic detected that Printer is out of
toner.

•

Toner Sensor (Q1)

•

Toner Sensor circuitry

•

Toner / Developer Car-
tridge

•

Main PWB (A3)

BSD 

9.7

PL 9.7
PL 1.1

Table 1 Status Code Entry Chart

Status
Code

Description

Components

BSD 

Ref

PL

Ref

Содержание Synergix 8850

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды