Xerox Synergix 8850 Скачать руководство пользователя | Manualshive

Страница: 38 / 432

background image

03/2003

2-4

8850/ 510DP

J1-01 Undertoned Fault RAP

Status Indicator RAPs

J1-01 Undertoned Fault RAP

NOTE: Go to

while using this RAP.

The status code J1-01 is displayed when the logic detects that the toner concentration is signif-
icantly less than the Control Point value.

The Toner Control System is designed to maintain the Toner Concentration within an accept-
able operating range. The Control Point operating range is from 4.4 to 6.0 VDC. The Toner
Sensor continuously senses the Toner Concentration. A change in the Toner Concentration
results in a corresponding change of the Sensor signal. As the Toner Concentration
decreases, the Toner Sensor signal voltage increases. The logic monitors the Toner Sensor
signal.

J1-01 indicates that the logic detected that the Toner Sensor Control Point is 1.2 or greater.
This means that the decrease in toner concentration is greater than the allowable limit.

The problem may occur if there is a problem with the toner dispensing or the developer mixing
systems.

Initial Actions

•

Examine the Toner Cartridge to ensure that the Cartridge is not empty and is installed
correctly.

•

Check the Cartridge for damage and ensure that the seal is secured to the Cartridge in
the correct location.

•

(

) Ensure that the Developer Drive Coupling is in good condition and is engaged

fully.

•

(

) Ensure that the Developer Housing Auger and Drive Gears are not damaged

and are installed correctly.

•

Check that all the connectors at the Toner Sensor, A22Q1P/J 1, and the Main PWB, A3P/
J 606, are seated correctly.

•

Check that the daughter PWB, that is mounted vertically on the HVPS, is fully seated.

•

Perform [0904] Automatic ESV Setup [

]. If an 0904 Automatic ESV Setup Failed,

Condition X is displayed, go to [

09 04 Automatic ESV Setup Failed

Procedure

With the printer in an J1-01 fault condition, enter diagnostic code [9-22] and press YES, in
order to enable the printer to function with an J1-01 fault condition. Enter the code [0361] in
order to exit the diagnostics mode.

Figure 1 Location of Developer Drive Coupling

The Developer Housing Auger and Drive Gears are rotating as the prints are being
made.

Cartridge Drive
Motor

Developer Drive
Gears

Developer Drive
Coupling

Main Drive Gear

Drum Drive Gear

«
...
36
37
38
39
40
...
»

Содержание Synergix 8850

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Synergix 8850

Бренд: SPRT Страницы: 28

Бренд: Oki Страницы: 45

Бренд: Zebronics Страницы: 6

Бренд: Canon Страницы: 4

201021 - P 330N Photo Printer

Бренд: Olympus Страницы: 79

Бренд: Oki Страницы: 255

Бренд: Riso Страницы: 208

AirLive WP-203G

Бренд: Ovislink Страницы: 132

Бренд: Lexmark Страницы: 2

Бренд: Roland Страницы: 116

Бренд: Star Страницы: 2

Бренд: Xante Страницы: 3

SPECTRUM Z M510

Бренд: Z Corporation Страницы: 7

Бренд: Canon Страницы: 776

imageRUNNER ADVANCE DX C7700 Series

Бренд: Canon Страницы: 127

Бренд: Canon Страницы: 146

Бренд: Xerox Страницы: 6

Бренд: CraftUnique Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды