manualshive.com logo in svg

Xantrex PV100S-480, Планирование и руководство по установке

Поделиться
Скачать
Xantrex PV100S-480 Скачать руководство пользователя страница 75

Visual Inspection of Mechanical Connections

152315 Rev C

4–3

Visual Inspection of Mechanical Connections

To perform a visual inspection of the PV100S mechanical connections:

Visual Inspection of Electrical Connections

To perform a visual inspection of the PV100S electrical connections:

1. Ensure that the AC and DC Disconnect Switches, as well as any utility 

interconnect circuit breakers or main disconnect switches, are opened.

❐

2. Ensure all anchor bolts and any required seismic bracing is properly 

tightened and in place.

❐

3. Remove the wiring access panels and front covers from the AC 

Interface/Transformer assembly and Main Inverter Inductor Enclosure.

❐

4. Remove the latches and open the doors of the Main Inverter Enclosure, 

the AC and DC Interface Enclosures, and Communication Enclosure 
and inspect.

❐

5. Verify all wire conduit fittings and connections are properly tightened.

❐

1. Ensure that the AC and DC disconnect switches, as well as any utility 

interconnect circuit breakers or main disconnect switches, are opened.

❐

2. Ensure all conductors and wiring connections interfacing with the 

PV100S are tightened to the correct torque value. 
For specific torque values, see Table 3-1, “AC Terminal Wire Gauge, 
Bolt Size, and Torque Values” on page 3–12 and Table 3-2, “DC 
Terminal Wire Gauge, Bolt Size, and Torque Values” on page 3–12.

❐

3. Verify AC power conductors terminated at TB4-A, TB4-B, TB4-C 

within the Main Inverter Enclosure are terminated correctly and 
properly sequenced.

❐

4. Verify the AC power conductors terminated at S1-2T1, S1-4T2, S1-6T3 

within the AC Interface Enclosure are terminated correctly and properly 
sequenced.

❐

5. Verify DC power conductors terminated at TB3-1, TB3-2, TB3-3 within 

the DC Interface Enclosure are terminated correctly and properly 
polarized.

❐

Содержание PV100S-480



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды