manualshive.com logo in svg

Xantrex PV100S-480, Планирование и руководство по установке

Поделиться
Скачать
Xantrex PV100S-480 Скачать руководство пользователя страница 32

Introduction

1–12

152315 Rev C

PC Connection Methods

Personal computers can be used to access the system status and programming 
features of the PV100S. A computer can be connected either directly or remotely. 
1. Remote Connect - uses one of the three kits below.

•

POTS Kit - uses a MultiTech® 56K Modem, RS232/Fiber Optic 
Converter (configured for ethernet) and SA2 Surge Arrestor.

•

Wireless Kit - uses a GSM Wireless Modem.

•

Ethernet LAN Kit - uses a data communication device to enable the unit 
to connect to a local area network. 

2. Direct Connect - This method is used for troubleshooting. It uses a 

RS232/Fiber Optic Converter (configured for a PC), a DB25-to-DB25 gender 
changer, and a DB25-to-DB9 Serial Cable. 

Software is included to provide a graphic user interface that relates important 
system information. This software is called Xantrex Solar Graphic Interface 
(GUI). See

 

"Computer Communications with the PV100S" in the PV100S 100 

kW Grid-tied Photovoltaic Inverter Operation and Maintenance Manual for 
additional information. 
The GUI can dial up the inverter and receive fault report calls from it through a 
standard Hayes-compatible, landline modem. When the GUI initiates a call 
through the modem at the GUI computer, the inverter’s modem answers the call 
and initiates a 9600 baud serial connection, effectively as if the GUI was 
connected directly. Or, if the inverter experiences a fault, it will initiate a call to 
the GUI and report the fault details. 

Figure 1-6

PC Connections in the Communications Enclosure

Communications 
Enclosure

MultiTech

®

 56K Modem

RS232/FO Converter

SA2 Surge Arrestor

Communications Enclosure

Enlargement

POTS connection option shown.

Содержание PV100S-480



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды