manualshive.com logo in svg

Xantrex PV100S-480, Планирование и руководство по установке

Поделиться
Скачать
Xantrex PV100S-480 Скачать руководство пользователя страница 25

System Specifications

152315 Rev C

1–5

System Ground Requirements

This product is intended to be installed as part of a permanently grounded 
electrical system per the National Electric Code ANSI/NFPA 70. A copper ground 
rod must be installed within three feet of the PV100S enclosures and connected to 
the unit as described in “System Grounding” on page 3–12. The single-point 
ground for the system is to be made at the AC ground bus bar (TB2) in the AC 
Interface Enclosure.

System Neutral Requirements

The PV100S is designed to be installed as a 4-wire system. As required by the 
UL 1741 listing, a neutral conductor from the utility-interconnect must be 
terminated at TB6 within the AC Interface Enclosure to ensure that the AC 
voltage sensing circuit can perform an individual phase voltage (line-to-neutral) 
measurement. The function of the neutral connection is to provide a point of 
reference for measurement purposes that is essentially at ground potential. No 
power will flow through the neutral conductor.

Utility Side Isolation Transformer Requirements

The PV100S is supplied with a custom, high-efficiency, isolation transformer as 
part of the AC Interface/Transformer assembly. The utility side windings of the 
isolation transformer are configured Wye and must match the voltage at the utility 
inter-tie. The PV100S is a balanced, three-phase, current-sourcing inverter and 
only operates with the presence of a stable utility voltage. The transformer is also 
supplied with a neutral connection on the utility interconnect. Connection of this 
utility-side neutral does not affect the operation of the inverter, however 
connection of the neutral on the inverter-side does affect the operation and must 
be left floating or disconnected. Single-phase, grounded loads which may be 
present between the transformer and utility, will maintain their existing ground 
reference at the utility distribution transformer.

CAUTION: Equipment Damage

If the Isolation Transformer (T6-X0) neutral terminal is tied to ground, it will cause 
irreparable damage to the PV100S. Check local regulations for their requirements 
regarding the connection of the neutral.

WARNING: Lethal Voltage

Grounding the neutral of a Wye-wound transformer may create an “open delta” condition, 
depending on the utility configuration. This condition may keep the PV100S from 
detecting a loss of phase condition on the utility system, which may allow potentially 
lethal voltage to be present on the open-phase wiring.

Содержание PV100S-480



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды