manualshive.com logo in svg

Xantrex PV100S-480, Планирование и руководство по установке

Поделиться
Скачать
Xantrex PV100S-480 Скачать руководство пользователя страница 59

Wiring - General

152315 Rev C

3–11

Overcurrent Protection

AC overcurrent protection for the Utility Interconnect (Grid-tie) must be provided 
by the installer as part of the PV100S installation. 

Conductor Termination

The PV100S has terminals and bus bars for making all wiring connections 
required for the installation. All terminals used for making AC and DC 
connections require the use of copper conductors with an insulation rating of 
90 °C (or higher). For wire gauge, bolt size, and torque values for the AC 
terminals, see Table 3-1. For wire gauge, bolt size, and torque values for the DC 
terminals, see Table 3-2. 

Transformer 
Enclosure

The AC terminals in the Transformer Enclosure (

T6-X1, T6-X2, 

and

 T6-X3)

 

require the use of crimp-on type ring terminals or compression lugs. The terminals 
are one bolt per pole. 

See Figure 3-14 on page 3–15 for the location of these terminals.

Main Inverter 
Enclosure

The AC terminals in the Main Inverter Enclosure (

TB4-A, TB4-B, 

and

 TB4-C) 

have two openings per pole. These terminals do not require the use of crimp-on 
type ring terminals or compression lugs. 
See Figure 3-15 on page 3–16 for the location of these terminals.

AC Interface 
Enclosure

The AC line terminals in the AC Interface Enclosure (

S1-2T1, S1-4T2, 

and

 

S1-6T3)

 are one bolt per pole. These terminals require the use of crimp-on type 

ring terminals or compression lugs. 

See Figure 3-16 on page 3–16 for the location of these terminals.

The AC neutral terminal in the AC Interface Enclosure (

TB6

) has one bolt per 

pole and requires the use of crimp-on type ring terminals or compression lugs. 

See Figure 3-18 on page 3–18 for the location of this terminal.

DC Interface 
Enclosure

The DC terminals in the DC Interface Enclosure (

TB3-1, TB3-2, 

and

 TB3-3) 

have two openings per pole. These terminals do not require the use of crimp-on 
type ring terminals or compression lugs. 

See Figure 3-19 on page 3–19 for the location of these terminals

.

CAUTION: Equipment Damage

In accordance with the NEC, ANSI/NFPA 70 (Ninth Edition) the following branch-circuit 
overcurrent protection must be provided:
• 400A maximum for PV100S-208
• 200A maximum for PV100S-480

Important:

Keep these cables together as much as possible, and ensure that all cables 

pass through the same knockout and conduit fittings, thus allowing any inductive currents 
to cancel.

Содержание PV100S-480



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды