manualshive.com logo in svg

Xantrex PV100S-480, Планирование и руководство по установке

Поделиться
Скачать
Xantrex PV100S-480 Скачать руководство пользователя страница 45

Conductor and Conduit Sizing

152315 Rev C

2–11

Conductor and Conduit Sizing

All wiring methods and materials shall be in accordance with the National 
Electrical Code ANSI/NFPA 70. When sizing conductors and conduits interfacing 
to the PV100S, both shall be in accordance with the National Electric Code 
ANSI/NFPA 70, as well as all state and local code requirements. 
Large gauge wire must conform to the minimum bend radius dependent upon the 
wire gauge

 

(refer to the National Electric Code, Article 373-6B (Ninth Edition). 

The following provides information on sizing the conductors and conduits for the 
system.

To calculate the proper conduit size:

1. Determine the required cable ampacity.
2. Determine the conduit length between the inverter and the transformer.
3. Determine the proper size for the cable according to the allowable ampacities 

indicated by NEC Table 310.16 (Ninth Edition).

4. Determine the proper size for the conduit.

The following is an example of the steps outlined above. Assumptions were made 
in this example which may not match your application, and the resulting design 
may not comply with all code requirements. Consult a licensed electrician on 
recommendations for specific installations. 

Step 1. Determine the required cable ampacity.

AC Phase Cables from Inverter to Transformer:

100 kW / 208 Vac / 1.732 = 277.5 A

rms

 (full load current)

277.5 x 125% = 347 A (required ampacity)

Step 2. Determine the conduit length between inverter and transformer.

•

If the conduit length between the inverter and the transformer is less than 
24 inches, then the cable can be sized using the NEC Table 310.16 
(in Raceway) (Ninth Edition). 

•

If the conduit length is greater than 24 inches, then the cable must be sized 
using NEC Table 310.16 (in Raceway) (Ninth Edition) and by using the 
adjustment factors in NEC TAble 310-15(b)(2)(a).

CAUTION: Equipment Damage

Be careful to keep the wire bundles away from any sharp edges which may damage wire 
insulation over time.

Содержание PV100S-480



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды