manualshive.com logo in svg

Xantrex PV100S-480, Планирование и руководство по установке

Поделиться
Скачать
Xantrex PV100S-480 Скачать руководство пользователя страница 70

Installation

3–22

152315 Rev C

Establishing Wireless Connection

To connect a personal computer using the GSM Wireless modem:

1. Ensure the personal computer has the appropriate hardware installed to 

support this feature.

2. Install the GUI Software following the instructions in the PV100S 100 kW 

Grid-tied Photovoltaic Inverter Operation and Maintenance Manual.

3. Use the GUI to setup the connection information.

a) From the GUI Main page, click on <

T

OOLS

>

b) Click on the inverter icon for the inverter to be setup.
c) Click on the <

I

NVERTER

 D

ATA

>

d) Click on the <

C

ONNECTION

>

 tab.

e) Fill out the information required on the <

G

ENERAL

> page, the 

<

T

ELEPHONE

 F

AULT

 C

ONFIGURATION

> page, and the <

T

ELEPHONE

 

C

ONFIGURATION

> page.

Establishing an Ethernet LAN Connection

To connect a personal computer using the Ethernet LAN Connection:

1. Ensure the personal computer has the appropriate hardware installed to 

support this feature (i.e., Network Interface Card [NIC]).

2. Open the Communications Enclosure and plug the LAN cable (CAT5 cable) 

into the RJ45 Port of the SA2 Surge Arrestor marked "U

NPROTECTED

".

3. Install the GUI Software following the instructions in the PV100S 100 kW 

Grid-tied Photovoltaic Inverter Operation and Maintenance Manual.

4. Use the GUI to setup the connection information.

a) From the GUI Main page, click on the inverter icon for the inverter to be 

setup.

b) Click on <

C

OMMUNICATION

>.

c) Select "

C

ONNECT

 

TO

 IP A

DDRESS

" in the drop-down menu.

d) Fill in the IP address provided by the Internet Service Provider.
e) Click on the <

C

ONNECT

>

 button.

f) Click on the <

O

K

> button.

g) Repeat this procedure for each unit to be added to local area network.

Important:

Ensure the Wireless service has been established with the local service 

provider before proceeding.

Important:

Ensure the local area network has been established with the local service 

provider before proceeding.

Содержание PV100S-480



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды