manualshive.com logo in svg

Xantrex PV100S-480, Планирование и руководство по установке

Поделиться
Скачать
Xantrex PV100S-480 Скачать руководство пользователя страница 53

Mounting and Anchoring the Units

152315 Rev C

3–5

Mounting and Anchoring the Units

To mount and anchor the PV100S:

1. Predrill the floor or pad to accept 1/2" diameter masonry anchors or ensure it 

has pre-installed anchoring bolts that will fit the 5/8" mounting holes.

2. Lift the main inverter from beneath the lower enclosure with a forklift or 

pallet jack as shown in Figure 3-2 on page 3–4. Move the Main Inverter 
Enclosure into place. 

3. Lift the AC interface/transformer assembly from beneath the enclosure with a 

forklift or pallet jack as shown in Figure 3-2 on page 3–4. Move the AC 
interface/transformer assembly into place. 

4. Secure the Main Inverter Enclosure feet to the floor with a 1/2" diameter 

anchor bolts.

5. Secure the AC interface/transformer assembly enclosure feet to the floor with 

1/2" diameter anchor bolts.

Important:

Before proceeding with the installation, determine the location and layout 

of the components, conduit penetration locations, conductor and conduit sizing, and 
method for anchoring the unit. Ensure adequate space is provided for clearance for 
ventilation and serviceability. Review Chapter 2, “Planning” if necessary before 
proceeding.

Figure 3-3

Mounting Hole Locations

Mounting Holes for 
securing and anchoring 
the units.

Содержание PV100S-480



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды