manualshive.com logo in svg

Xantrex PV100S-480, Планирование и руководство по установке

Поделиться
Скачать
Xantrex PV100S-480 Скачать руководство пользователя страница 71

PC Communications

152315 Rev C

3–23

Direct Connection 

The direct connection provides the means to use the features of the GUI by 
connecting a PC directly to the CCU2. This allows field personnel to monitor and 
control the inverter from a nearby laptop computer directly connected by a serial 
cable. The computer connects to the inverter directly through one of its serial 
COM ports running at 9600 baud. 
The installed RS232/FO Converter will have to be removed and minor re-wiring 
will be required.
The RS232/FO Converter kit (Xantrex p/n 1-152624-01) is required for this 
connection to change the communication protocol from ethernet to serial in the 
Communications Enclosure. A DB25-to-DB25 gender-changer adapter and 
DB9/DB25 serial cable are provided with the RS232/FO Converter kit to 
complete the connection. 

If connecting the PC directly to the inverter:

1. Open the Communications Enclosure.
2. Disconnect the TX (transmit-orange) and RX (Receive-blue) wires from the 

installed RS232/FO Converter in the Communications Enclosure. 

3. Disconnect the power plug from the installed converter and plug it into the 

new RS232/FO Converter.

4. Remove the installed converter. Replace with the new RS232/FO Converter.
5. Reconnect the TX (transmit-orange) and RX (Receive-blue) wires to the new 

Converter in the Communications Enclosure. 

6. Plug the DB25-to-DB25 Gender-changer Adapter into the Serial 

Communications Port on the RS232/FO Converter. (Step not shown.)

7. Plug the DB25 connector on the serial cable into the gender-adapter and the 

DB9 connector of the serial cable into the serial port on the computer. (Step 
not shown.)

Figure 3-21

RS232/FO Converter Kit Installation

SA2 Surge Arrestor

MultiTech 56K Modem

Modem Power Cord
(Do not Remove)

3

2

4

Содержание PV100S-480



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды