manualshive.com logo in svg

wsm wg972-e4, Руководство по ремонту

Поделиться
Скачать
wsm wg972-e4 Скачать руководство пользователя страница 81

ENGINE

WG972-E4, WSM

1-M20

[8]  MIXER (GAS LINE) [WG972-GL, WG972-L, WG972-N]

Mixer (3) is a device to mix air and gaseous fuel with

proper ratio required by the engine. The gaseous LPG or
CNG fuel flows to the mixer through main jet (1) from the
Regulator with vaporizer.

When the engine starts, the LPG fuel flows out from

main jet (1) to venturi a constant amount and is mixed
with air quantity corresponding to the opening of the
throttle valve and is supplied to the cylinder.

9Y1211108ENM0032US0

(1) Main Jet (LPG / CNG)
(2) Regulator Reference Port 

(Connecting with Secondary 
Stage in Regulator)

(3) Mixer
(4) Electronic Throttle Body

A: Gaseous Fuel (LPG / CNG)
B: Blow-by Gas (From Head 

Cover)

C: Air
D: Mixture (Air and Fuel) 
a:

Air

b:

Vapor Fuel

c:

Mixture

KiSC issued 07, 2015 A

Содержание wg972-e4


























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды