wsm wg972-e4 Скачать руководство пользователя страница 70

Страница: 70 / 153

ENGINE

WG972-E4, WSM

1-M9

3. COOLING SYSTEM

[1] GENERAL

The cooling system consists of a radiator (1), a

centrifugal water pump (4), a suction fan (2) and a
thermostat (3).

The coolant is cooled through the radiator core, and

the fan behind the radiator pulls the cooling air through
the core to improve cooling.

The water pump sucks the coolant from the radiator

or from the cylinder head and forces it into the cylinder
block.

The thermostat opens or closes according to the

coolant temperature, to allow the coolant to flow from the
cylinder block to the radiator while open, or only to the
water pump while closed.

9Y1211108ENM0020US0

[2] COOLING FIN

The cooling fin is set up around the oil passage in the

gear case.

Therefore, the temperature of oil is decreased by the

wind generated by the cooling fan.

9Y1211108ENM0021US0

[3] WATER PUMP

The water pump is driven by the crankshaft and a V

belt. The rotating impeller (4) in the water pump sucks
the coolant from the radiator and sends it into the water
jacket in the cylinder block.

The mechanical seal (3) prevents the water from

entering the bearing unit (1).

9Y1211108ENM0022US0

Thermostat's valve
opening temperature

Factory
specifica-
tion

69.5 to 72.5 °C
157.1 to 162.5 °F

(1) Radiator
(2) Cooling Fan
(3) Thermostat

(4) Water Pump
(5) Cylinder Head
(6) Cylinder Block

(1) Cooling Fin

(1) Bearing Unit
(2) Water Pump Body

(3) Mechanical Seal
(4) Impeller

KiSC issued 07, 2015 A

Содержание wg972-e4


























































































































































Результаты поиска

Содержание wg972-e4

Отзывы:

Бренды по названию

Популярные бренды

wsm wg972-e4, Руководство по ремонту

Результаты поиска

Содержание wg972-e4

Отзывы:

Бренды по названию

Популярные бренды