wsm wg972-e4 Скачать руководство пользователя страница 111

Страница: 111 / 153

ENGINE

WG972-E4, WSM

1-S20

Spark Test

1. Disconnect all injector connector.
2. Remove the spark plug, put it inside the ignition coil firmly, and

then ground the threaded section to the engine body (not to
painted or resin parts).

3. Rotate the starter with the key switch and check that the plug

sparks.

4. If test is

, tighten the spark plug with a plug wrench.

IMPORTANT

(When reassembling)

• Put the ignition coil inside the spark plug terminal firmly.
• Make sure that the wiring and the ignition coil are correctly

connected.

• Make sure that the removed connectors are correctly

connected.

CAUTION

• This test is hazardous of electric shocks. Never use hand

or screwdriver to press the plug to ground it to the engine
body.

• Keep inflammable away from the engine.

NOTE

• Spark test can be done using the diagnostic tool. Refer to

Diagnosis Manual for more information.

9Y1211108ENS0022US0

Spark Plug Cleaning

1. Remove the spark plug, and remove carbon from the electrode

with a wire brush or other tools.

2. After cleaning, be sure to adjust for proper clearance.

IMPORTANT

• If the spark plug electrode or its insulator is soiled or is

covered with deposited carbon, it may cause engine
trouble.

9Y1211108ENS0115US0

KiSC issued 07, 2015 A

Содержание wg972-e4


























































































































































Результаты поиска

Содержание wg972-e4

Отзывы:

Бренды по названию

Популярные бренды

wsm wg972-e4, Руководство по ремонту

Результаты поиска

Содержание wg972-e4

Отзывы:

Бренды по названию

Популярные бренды