wsm wg972-e4 Скачать руководство пользователя страница 43

Страница: 43 / 153

GENERAL

WG972-E4, WSM

G-17

Replacing Fuel Filter (Gasoline Line) (If Necessary)
[WG972-GL, WG972-G]

1. Loosen clamps and remove the fuel hoses.
2. Replace the fuel filter with the new one.

CAUTION

• Stop the engine when trying to check and clean the fuel

filter.

• Gasoline fuel is extremely flammable, so avoid fires.

9Y1211108GEG0029US0

Checking Fan Belt Tension

1. Measure the deflection

(A)

, depressing the belt halfway

between the fan drive pulley and alternator pulley at specified
force 98 N (10 kgf, 22 lbf).

2. If the measurement is not within the factory specifications,

adjust the fan belt tension.

9Y1211108GEG0030US0

Checking Fan Belt Damage and Wear

1. Check the fan belt for damage.
2. If the fan belt is damaged, replace it.
3. Check if the fan belt is worn and sunk in the pulley groove.
4. If the fan belt is nearly worn out and deeply sunk in the pulley

groove, replace it.

9Y1211108GEG0031US0

Adjusting Fan Belt Tension (If Necessary)

1. Loosen the alternator mounting screws.
2. Relocate the alternator to adjust fan belt tension with the

specified deflection.

9Y1211108GEG0032US0

(1) Gasoline Fuel Filter
(2) Fuel Hose

(3) Clamp

Deflection

(A)

Factory specification

7.0 to 9.0 mm
0.28 to 0.35 in.

(A) Deflection

(A) Good

(B) Bad

Deflection

(A)

Factory specification

7.0 to 9.0 mm
0.28 to 0.35 in.

(A) Deflection

KiSC issued 07, 2015 A

Содержание wg972-e4


























































































































































Результаты поиска

Содержание wg972-e4

Отзывы:

Бренды по названию

Популярные бренды

wsm wg972-e4, Руководство по ремонту

Результаты поиска

Содержание wg972-e4

Отзывы:

Бренды по названию

Популярные бренды