wsm wg972-e4 Скачать руководство пользователя страница 105

Страница: 105 / 153

ENGINE

WG972-E4, WSM

1-S14

4. CHECKING, DISASSEMBLING AND SERVICING

[1] CHECKING AND ADJUSTING

(1) Engine Body

Compression Pressure

1. Operate the engine until it is warmed up.
2. Stop the engine.
3. Remove the air cleaner, the muffler/converter and all spark

plugs.

4. Set a compression tester with the adaptor to the spark plug

hole.

5. Operate the engine with the starter for 5 to 10 seconds keeping

throttle valve fully open and read the maximum compression
pressure.

6. Repeat steps 4 and 5 for each cylinder.
7. If the measurement is below the allowable limit, apply a small

amount of oil to the cylinder wall through the spark plug hole and
measure the compression pressure again.

8. If the compression pressure is still less than the allowable limit,

check the top clearance, valve clearance and cylinder head.

9. If the compression pressure increases after applying oil, check

the cylinder wall and piston rings.

NOTE

• Check the compression pressure with the specified valve

clearance.

• Always use a fully charged battery for performing this test.
• Variances in cylinder compression values should be under

10 %.

• Replace the muffler/converter gasket with a new one.

9Y1211108ENS0007US0

Compression pressure

Factory specification

1.27 MPa
13.0 kgf/cm

185 psi

Allowable limit

0.88 MPa
9.0 kgf/cm

130 psi

KiSC issued 07, 2015 A

Содержание wg972-e4


























































































































































Результаты поиска

Содержание wg972-e4

Отзывы:

Бренды по названию

Популярные бренды

wsm wg972-e4, Руководство по ремонту

Результаты поиска

Содержание wg972-e4

Отзывы:

Бренды по названию

Популярные бренды