manualshive.com logo in svg

wsm wg972-e4, Руководство по ремонту

Поделиться
Скачать
wsm wg972-e4 Скачать руководство пользователя страница 65

ENGINE

WG972-E4, WSM

1-M4

[7] CONNECTING ROD

The connecting rod (2) is used to connect the piston

with the crankshaft. The big end of the connecting rod
has a crankpin bearing (3) (split type) and the small end
has a small end bushing (1) (solid type).

9Y1211108ENM0009US0

[8] CAMSHAFT

The camshaft (1) is made of special cast iron, and

the journal and cam sections are chilled to resist wear.

The cams on the camshaft cause the intake and

exhaust valves to open as the camshaft rotates. The
bearing and journals are force-lubricated.

9Y1211108ENM0010US0

[9]  ROCKER ARM ASSEMBLY

The rocker arm assembly includes the rocker arms

(2) and adjusting screws (1), the end of which rests on
the push rods, rocker arm brackets (4) and rocker arm
shaft (3).

The rocker arms swing and transmits the

reciprocating motion of the push rods to the inlet and
exhaust valves to open and close them.

9Y1211108ENM0011US0

(1) Small End Bushing
(2) Connecting Rod
(3) Crankpin Bearing

(4) Connecting Rod Cap
(5) Connecting Rod Screw

(1) Camshaft
(2) Feather Key

(3) Camshaft Stopper
(4) Cam Gear

(1) Adjusting Screw
(2) Rocker Arm

(3) Rocker Arm Shaft
(4) Rocker Arm Bracket

KiSC issued 07, 2015 A

Содержание wg972-e4


























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды