Worx Generic QJ125-26A Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 166

Worx Generic QJ125-26A Скачать руководство пользователя страница 89

3. Braking shoe assembly improperly installed 3. Braking shoe assembly improperly installed
4. Braking shoe assembly and brake disc contaminated

Noisy Braking

1. Braking shoe assembly and brake disc are worn.
2. Braking shoe assembly and brake disc are contaminated

5.3 Front Hydraulic Brake

5.3.1 Removal

* Attention

• Replace braking shoe assembly.
• If a braking shoe assembly will be used
again, please mark it on the side before
removal so as to re-install it to its original
place

Remove from right handle and front shock
absorber the following assemblies.
Front brake:

1. Hydraulic brake handle

（

7

）

2. Oil pump block assembly

（

5

）

3. Braking hose assembly

（

4

）

4. Braking cylinder assembly

（

6

）

5. Hydraulic brake disc

（

2

）

Note: Detailed breakdown drawing refers to P85.

* Attention

•Please do not contaminate braking shoe assembly with oil
while assembly or disassembly
•Please use specified detergent to clean the braking assembly,
or it may reduce braking performance.
Screw off braking cylinder assembly mounting bolt.
Remove the braking cylinder assembly from front shock
absorber.
Remove front wheel shaft.
Remove front wheel.
Remove brake disc from the front wheel.

5.3.2 Inspection

Check if braking shoe assembly and brake disc are worn. Replace them if necessary.
Measure braking shoe and brake disc and record the maximum values.

«
...
87
88
89
90
91
...
»

Содержание Generic QJ125-26A







































































































































































Отзывы:

Нет отзывов