Worx Generic QJ125-26A Скачать руководство пользователя страница 10

Страница: 10 / 166

Slack cable implies potential safety hazard on electrics. Check

the next cable when the cable is clamped to ensure electric safety;

Cable clamp shall not be bent towards solder joint;

Tie the cable at appointed position;

Do not lay the cable at the end of frame or at the closed angle;

Do not lay the cable at the end of a bolt or screw;

Wiring of cable shall be away from heat source or places where

cable may be clipped while moving;

Prevent the cable from being pulled too tightly or slacking too

much when the cable is wired along the handle pipe. The cable

shall not be affected by any neighbored components at any

turning position;

The cable shall be wired smoothly and shall not be knotted or

twisted;

Check if the sheath of connector is damaged and if the connector

is over stretched before butt joint connection;

If cable runs around the closed angle or the corner, please protect

it with tape or hose;

Tie the cable with adhesive tape reliably when it is repaired;

The controlling cable shall not be bent or twisted. Broken

controlling cable will result in non-flexible control.

Содержание Generic QJ125-26A







































































































































































Результаты поиска

Содержание Generic QJ125-26A

Отзывы:

Worx Generic QJ125-26A, Инструкция по эксплуатации и техническому обслуживанию, Страница: 10 / 166

Результаты поиска

Содержание Generic QJ125-26A

Отзывы: