Worx Generic QJ125-26A Скачать руководство пользователя страница 30

Страница: 30 / 166

Symptom: Battery cannot charge Diagnosis procedures

Yes

Wire from connector to

battery is broken.

Set multimeter on 0V~20V DC voltage, measure the

voltage between lead wire terminal from connector to the

battery (usually a red or red/white wire) and the ground.

Wire from magneto to rectifier or wires

among rectification regulators are not well

connected or broken.

No voltage display

Voltage displays

Check with an Ohmmeter if rectifier or

rectification regulator fails.

Battery cannot charge

Resistance is less than standard.

Charging coil is shorted.

Resistance is infinitely great.

Resistance meets the standard.

Charging coil or its

output wires are

shorted.

Disconnect connectors of magneto lead wire tied to the cables of the whole motorcycle.

Measure with an Ohmmeter between out-put wires from charging coil

Connect connectors of magneto lead wire harness to the

cables of the whole motorcycle; break off connectors of rectifier

or regulator to cables of the whole vehicle.

Measure with an Ohmmeter on the resistance in the connectors

between output wires from charging coil, and check if the result

is in accordance with the resistance of the charging coil itself.

Содержание Generic QJ125-26A







































































































































































Результаты поиска

Содержание Generic QJ125-26A

Отзывы:

Worx Generic QJ125-26A, Инструкция по эксплуатации и техническому обслуживанию, Страница: 30 / 166

Результаты поиска

Содержание Generic QJ125-26A

Отзывы: