Worx Generic QJ125-26A Скачать руководство пользователя страница 127 | Manualshive

Страница: 127 / 166

Worx Generic QJ125-26A Скачать руководство пользователя страница 127

Clogged oil filter

Too high or too low mixed gas concentration

Clogged oil pipe

Secondary air sucked by the intake system

Sticky

needle

value

Improper

idle

adjustment

Improper oil level adjustment

Improper oil level adjustment
Clogged idle system or electric enrich valve

Too much fuel in engine

Too low mixed gas concentration

Oil outflow                                                      Clogged oil nozzle
Secondary air sucked by fuel system      Clogged needle valve
Degraded fuel                                                 Too low oil level
Improper work of enrich valve            Clogged fuel system
Clogged idle system or choke system          Improper work

of

plunger

Secondary air sucked by the intake system

Too high mixed gas concentration

Intermittent spark while acceleration

Improper work of enrich valve Too low mixed gas concentration
Improper work of needle valve
Too high oil level
Oil outflow from carburetor
Clogged airway
Dirty air cleaner

11.3 Removal of Carburetor

11.3.1 Removal

Remove the locknut between carburetor and bakelite washer.
Remove carburetor assembly.

11.3.2 Disassemble Carburetor

Screw off upper cover and remove sealing ring, plunger spring and plunger assembly on it.
Screw off lower housing connecting screw and remove lower housing assembly and sealing ring.
Remove float assembly, float pin and needle valve core.
Remove idle jet, main jet, main nozzle and main foam pipe.
Remove mixture screw, mixture screw spring, mixture screw washer and mixture screw sealing ring.
Remove plunger adjusting screw and plunger adjusting screw spring.

For details, refer to breakdown diagram in P125.

«
...
125
126
127
128
129
...
»

Содержание Generic QJ125-26A







































































































































































Отзывы:

Нет отзывов