Worx Generic QJ125-26A Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 166

Worx Generic QJ125-26A Скачать руководство пользователя страница 71

Connecting method: positive (+) to blue/white, negative (-) to green/white.

Min. voltage: higher than 1.7V.

* Attention

Please do not touch the metal parts of testing probe with your
fingers while measuring the voltage, or you will be shocked.
Please take care.

When the peak voltage measured at connector of CDI
assembly is abnormal, take down the protecting plate on the
right side of vehicle and remove connector of magneto.
Trigger (blue/white) is connected with a shunt.
• When the measured voltage at CDI assembly terminal is abnormal, but measured voltage at magneto terminal is

normal, it indicates that the connector is of poor contact or wiring is broken.

• When measured results at both sides are abnormal, the trigger is damaged. Please refer to items listed in Diagnosis
Table and check.

2.4 CDI Assembly

2.4.1 System Inspection

System inspection
Remove CDI assembly and check components related to the ignition
system at wiring terminal.

2.4.2 Inspection

Remove CDI assembly and check if connectors are loosen or
corrosive.

Item Measuring

terminal

Standard

Value

（

20

）

Main switch

Red—Red/White

On continuity when main switch is

“OFF”.

Trigger

Blue/White-White/Green

100-200

Ω

Primary coil of ignition

coil

Black/White—Black 0.4

Ω

±10

％

Secondary coil of ignition

coil

Black—spark plug cap

（

not including spark

plug

）

3-5.5K

Ω

±10

％

«
...
69
70
71
72
73
...
»

Содержание Generic QJ125-26A







































































































































































Отзывы:

Нет отзывов