Worx Generic QJ125-26A Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 166

Worx Generic QJ125-26A Скачать руководство пользователя страница 82

4.5 Tail Lamp Bulb Replacement

4.5.1 Removal

Screw off the two bolts

（

1

）

.

Remove the tail lamp hood.
Disconnect wire connector to the tail lamp.
While pressing down the tail lamp, rotate it counterclockwise
Remove the tail lamp

4.5.2 Installation

Install the tail lamp in the reverse order of removal.

* Attention

While installing tail lamp, be sure that sealing washer on the
tail lamp hood is in good condition and correct position.

4.5.3 Tail lamp bulb replacement

4.5.3.1 Removal

Screw off mounting bolts on the tail lamp hood.
Remove tail lamp hood

（

3

）

so that tail lamp bulb can be removed.

Remove the tail lamp bulb from lamp adapter

（

2

）

.

4.5.3.2 Installation

Install the tail lamp bulb in the reverse order of removal

4.6 Instrument

Remove rear mirror.
Take down the handle hood and pull out waterproof connector.
Remove the screw.
Remove odometer assembly.
Remove the instrument.
Install the instrument orderly in the reverse order of removal.

«
...
80
81
82
83
84
...
»

Содержание Generic QJ125-26A







































































































































































Отзывы:

Нет отзывов