Worx Generic QJ125-26A Скачать руководство пользователя страница 161

Страница: 161 / 166

16.4 Crankshaft Connecting Rod Assembly

Removal

Remove left crankcase.
Remove washer and location pin.
Remove drive gear.
Remove the crankshaft connecting rod assembly from the right
crankcase.

* Attention: Please do not hurt washer and closing surface

Inspection

Measure connecting rod big end left-to-right clearance.

Allowable limit: 0.55mm.

Measure connecting rod big end clearance along X-Y direction.

Allowable limit: 0.05mm.

Crankshaft shimmy measurement.

Allowable limit: 0.01mm.

Check if there is abnormal noise and looseness when the
crankshaft is rotating.
If there is, replace the crankshaft.

* Attention:

Install together crankshaft connecting rod assembly and gearshift
mechanism on the crankcase.

Crankshaft connecting

rod assembly

Location pin

Washer

Drive gear

Measuring position of C.R big end

Crankshaft bearing

Содержание Generic QJ125-26A







































































































































































Результаты поиска

Содержание Generic QJ125-26A

Отзывы:

Worx Generic QJ125-26A, Инструкция по эксплуатации и техническому обслуживанию, Страница: 161 / 166

Результаты поиска

Содержание Generic QJ125-26A

Отзывы: