Worx Generic QJ125-26A Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 166

Worx Generic QJ125-26A Скачать руководство пользователя страница 112

8.4.5 Rear Swing Arm Inspection

Check rear swing arm installation shaft. Rotate the shaft on a flat
surface or measure it with a dial gauge. If it is bent, replace it.

* Attention

Don’t attempt to straighten bent shaft.

Wash in solvent the components for rear swing arm installation
shaft.
Check sleeve assembly of rear swing arm

（

7

）

and intermediate

sleeve (5).
If they are damaged, replace them.

8.4.6 Install Rear Swingarm

Install the rear swing arm in the reverse order of removal.
Apply lubricating grease on to pivot bush.
Install rear swing arm

sleeve

assembly

（

15

）

and intermediate

sleeve

（

14

）

.

Install rear swing arm assembly

（

6

）

.

Install rear swing arm onto the frame and insert rear swingarm shaft.
Install and tighten rear swing arm shaft nut to specified torque.
Install lower mounting bolt on rear shock absorber.
Install drive chain cover.
Install the two connecting bolts.
Install rear wheel.

Install rear swing arm nut
Tightening torque: 70-83N·m

8.5 Chain Drive Assembly

8.5.1

．

Removal

Stop the motorcycle on the flat ground and
stand it steadily.
Remove gearshift pedal connecting parts,
drive chain cover and drive sprocket.
Remove rear wheel, rear shock absorber,
chain cover and drive chain.

8.5.2

．

Inspection

Measure length

of 10 chain links. If they cannot meet the specified value, replace the drive chain.

«
...
110
111
112
113
114
...
»

Содержание Generic QJ125-26A







































































































































































Отзывы:

Нет отзывов