Worx Generic QJ125-26A Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 166

Worx Generic QJ125-26A Скачать руководство пользователя страница 51

may result in explosion.
• During charging, please take the current time labeled on the battery as basic time.

* Attention

• Battery quick recharging is not recommended except in case of emergency.
• After recharging, wait at least 30minutes and then measure the battery voltage.

Recharging current: Standard: 0.3A

Quick recharging: 3.0A

Recharging time:

Standard: 10-15hours

Quick recharging: 30minutes

After recharging:

Open circuit voltage: over 12.8V

Carburetor

Idle speed adjustment

*

Attention

Perform idle speed adjustment when the engine is warm.

Warm up the engine and then adjust idle speed.
Run the engine and connect engine tachometer.
Adjust the throttle cable lock-screw to specified RPM.

Idle speed RPM: 1400±100rpm/min

If idle speed RPM is unsteady, or idle speed is not smooth when
gently raise engine speed, adjust idle speed adjusting screw again.

Ignition Timing

* Attention

Inspect ignition system when the ignition timing is incorrect.
Warm up the engine for 3~5 minutes
Stop the engine and connect the timing lamp to lead wire of spark
plug.
Remove timing hole cap.
Start engine and idle it.
Inspect ignition timing.
If symbol “F” aligns to the mark on the right crankcase, it indicates that the ignition timing is correct. Increase engine
speed and check if Symbol “F” begins to move.

«
...
49
50
51
52
53
...
»

Содержание Generic QJ125-26A







































































































































































Отзывы:

Нет отзывов