6
Routing the Wiring................................................... B-2
RS-232 Cable Pin-outs ............................................. C-1
RS-232 Extension cables.......................................... C-1
RS232 problems.......................................................... 8-6
RS-422 Termination Jumpers................................... A-2
RSS-14 code ............................................................2-14
S
Scanner input only - breaking out of.........................6-3
scanning through a windshield ................................. L-3
SEARCH key
transmitting ASCII 11 to host .............................6-12
Security Code - setting on Terminal .........................2-6
Security Code for Base or Relay................................. 2-23
Selective data trimming by bar code type ..... 2-16, 2-17
Sequence Error ..........................................................8-3
Sequence Error Message .........................................6-10
Serial cables
"noise" problems ...................................................4-4
serial device attachment ............................................6-3
serial input on Terminal ............................................6-3
Serial keyboard input.................................................6-3
Serial output command for terminal .........................6-4
Serial pin-outs........................................................... C-1
Serial printer setup paramters on terminal ..............2-21
Serial Reply - Base to host programming .................6-7
Set Date ...................................................................2-19
Set Time...................................................................2-19
Setting serial parameters on your Base or Relay ....2-23
Setting the Relay ID ................................................. A-2
Setup
RF Terminal ..........................................................2-5
Setup Cloning to other terminals...............................7-5
Setup Menu
"Reset" bar code ..................................................2-21
Baud Rate ............................................................2-21
Data Bits ..............................................................2-21
Parity ...................................................................2-21
RF Terminal Channel ............................................2-5
RF Terminal parameters........................................2-5
Stop Bits ..............................................................2-21
Terminal ID ...........................................................2-5
SETUP MODE
using to program voice messages..........................7-2
Setup or playback voice messages ............................7-3
shelf label printing...................................................6-34
Shut Down Time .....................................................2-20
Shut Down Time feature ...........................................1-4
SIGN ON Base to host programming .......................6-8
SIGN OUT
Base to host programming ....................................6-9
missing the message ..............................................5-3
Signing out in mid-transaction ..................................5-2
Site survey .................................................................3-5
Site Test Mode - brief description of .......................3-1
Site Testing
channel changes ..................................................... 4-2
getting into.............................................................1-7
how it works ..........................................................3-5
Site Testing in Progress message ..............................4-2
Six beeps on power-up ..............................................8-6
Skip Opening Screens ...............................................2-8
sleep mode for RF Terminal......................................3-3
SPEAKER VOLUME ...............................................2-9
Stand mode ......................See hands free laser scanning
Start Setup
scanning to enter Setup mode ...............................2-2
Start/stop characters
transmitting for Codabar........................................ 2-13
transmitting for Code 39 ..................................... 2-10
STATUS key
reserved for date/time only ................................. 6-12
using to determine battery life ............... 1-5, 2-8, 8-2
Steps for installation.................................................. 1-1
STK bar code ............................................................ 2-12
Stop Bits for serial printer ....................................... 2-21
Storage Tek bar code ................................................. 2-12
Storage Tek Tape Label code..................................... 2-12
substitution errors......................................................L-2
Substitutions of data ..................................................L-3
sunlight problems, using aiming dot .........................L-3
Surveying a site ......................................................... 4-1
T
T49 Holster for RF Terminal ................................... N-4
Tape library bar code................................................. 2-12
TCP/IP Terminal Programming .............................. 6-23
Terminal ID
how to find out what yours is................................ 1-7
use in Two-Way mode .......................................... 3-2
Terminal ID in One Way mode................................. 3-5
Terminal keys
transmitting ASCII values..................................... 2-6
Terminal setup
Security Code ........................................................ 2-6
Terminal Setup Cloning
to other terminals .................................................. 7-5
Terminating a programming message....................... 6-2
Terminator character ............................................... 2-16
Testing Base Station communications .............2-23, 8-5
Testing communication with a Relay....................... B-4
Testing the Relay...................................................... B-4
Thru-put considerations ............................................ 4-6
Time Set .................................................................. 2-19
time stamping in Terminal ........................................ 6-3
Tips for Using Voice Prompts................................... 7-1
Trailing character trimming .................................... 2-17
TRANSMISSION FAILED ...............................3-3, 3-4
Transmitting Bar Code ID's .................................... 2-12
Transmitting characters before or after
bar code data........................................................ 2-15
Transmitting Codabar start and stop characters ........... 2-13
Transmitting EAN-8/UPC-E in original formats ...... 2-12
Transmitting through walls .......................................... 4-1
Trimming by bar code type
using bar code ID and postamble........................ 2-17
using bar code ID and preamble/postamble ............ 2-16
Trimming characters from data......................2-15, 2-17
Trimming leading characters using Preamble......... 2-15
Trimming trailing characters using Postamble ....... 2-16
TriOptic Code 39 ...................................................... 2-12
Troubleshooting ........................................................ 8-1
electrical noise problems with Relays................... 4-4
wiring problems with Relays ................................ 4-4
Troubleshooting new installation.............................. 8-2
Turning on the R/F Terminal .................................... 1-4
turns off and on by itselt............................................ 8-6
Two-Way Mode
brief description of ................................................ 3-1
in depth description of how it works..................... 3-2
Typical coverage ....................................................... 4-5
U
UCC 128 Serial Shipping Container bar code ......... H-2
