manualshive.com logo in svg

Worcester GR2300iW C, Инструкция по установке и обслуживанию

Поделиться
Скачать
Worcester GR2300iW C Скачать руководство пользователя страница 83

Fault finding and diagnosis

83

Greenstar 2000 – 6 721 820 552 (2021/02)

Table 36 Indicators and fault displays

2964 B

Flow rate in heat exchanger too low

▶ Check the flow through the appliance and that the system is filled.
▶ Check for air locks in the system and purge if required.
▶ Check the heat exchanger sensor (primary thermistor) and the plug connected to the 

temperature sensor.

▶ Check the resistance of the temperature sensor and replace if required.
▶ Check the continuity of the harness and replace if required.

2965 B

Flow temperature too high

▶ Check the flow through the appliance and the system is filled.
▶ Check for the air locks in the system and purge if required.
▶ Check the isolation valves.

2966 B

Flow temperature rise in heat exchanger too 
rapid

▶ Check the flow through the appliance and the system is filled.
▶ Check for the air locks in the system and purge if required.
▶ Check the isolation valves.
▶ Check the pump is operating freely and check the voltage to the pump.

2967 B

Flow/heat exchanger temperature sensor 
differential too great

▶ Check the flow through the appliance and the system is filled.
▶ Check for air locks in the system and purge if required.
▶ Check the isolation valves.
▶ Check the pump is operating freely and check the voltage to the pump.
▶ Check the heat exchanger sensor and the flow sensor are making contact with the 

pipework.

▶ Check the heat exchanger sensor and the resistance of the temperature sensor and 

replace if required.

▶ Check the continuity of harness and replace if required.

2972 – 

Mains voltage too low

Check the mains voltage on the appliance (L and N).

2973 – 

System fault boiler electronics / basic 
controller

▶ Perform factory reset.
▶ Check and replace control unit.

2974 – 

Internal fault

▶ Restart the appliance and check if fault remains.
▶ Check and replace control unit.

3071 – 

C II RF

▶ Check the configuration (address setting). The selected setting requires a remote 

control.

▶ Check the EMS connection cable for the remote control for damage. The BUS voltage on 

the remote control must be between 12 and 15 V DC.

▶ The remote control is defective.

Fa

ult

 

co

de

Fa

ult

 

ca

te

go

ry Description

Remedy

Содержание GR2300iW C





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды