Worcester GR2300iW C Скачать руководство пользователя | Manualshive

Страница: 11 / 100

background image

Product Information

11

Greenstar 2000 – 6 721 820 552 (2021/02)

Legend to figure 3:

[1]

Inspection aperture

[2]

Flue connection

[3]

Heating block temperature limiter

[4]

Electrode set

[5]

Ignition transformer

[6]

Control pressure test point

[7]

Gas-air mixing chamber

[8]

Heating block

[9]

Gas valve

[10] Condensate sump
[11] Cover for inspection aperture
[12] Diverter valve motor
[13] Diverter valve
[14] Automatic air vent
[15] Heating pump
[16] Pump speed adjuster and LED indicator
[17] Pressure relief valve (heating circuit)
[18] Plate heat exchanger
[19] KEY accessory housing (wireless gateway)
[20] Pressure gauge
[21] Position for code plug (KIM)
[22] Control unit
[23] DHW temperature sensor
[24] Pressure switch
[25] Flow turbine
[26] Fuse (replacement)
[27] Condensate trap
[28] Data plate
[29] Condensate trap locking mechanism
[30] Gas supply pressure test point
[31] Flue gas temperature limiter
[32] Flow temperature sensor
[33] Schrader valve
[34] Expansion vessel
[35] Fan
[36] Air-gas manifold with non-return valve
[37] Heating flow
[38] Flow temperature sensor at heating
[39] Bracket
[40] Combustion air intake

3.7

Product data for energy consumption

The product data on energy consumption can be found in the operating
instructions for the user.

3.8

Standard accessories

3.8.1

Appliance accessories

Table 5 Appliance accessories

3.8.2

Programmer/timer accessories

The programmers/timers listed can be used with the appliances stated
on the front of this manual.

Table 6 Control accessories

Bosch EasyControl smart control system

Table 7 EasyControl accessories

Basic weather compensation sensor

Outdoor weather sensor (to activate on-board simple Weather
Compensation).

Table 8 Control accessories

The outdoor weather sensor is supplied with the Sense II. It is optional
with the II RF. Weather compensation is available with the
EasyControl without the need for a physical outdoor sensor, however, it
can improve control accuracy for installations in isolated micro-climates
or highly sheltered locations such as valleys.

Part number

Description

7 733 600 266

Greenstar System filter (22mm mini)

7 733 600 236

Greenstar System filter (22mm)

7 733 600 237

Greenstar System filter (28mm)

7 733 600 476

Greenstar System filter brass (22mm)

7 716 192 746

Worcester CondenseSure

7 716 192 610

Keyless filling link kit

7 733 600 091

Heat exchanger cleaning kit

7 736 902 107

Low NOx code plug kit 25kW

7 736 902 108

Low NOx code plug kit 30kW

7 736 900 525

Greenstar Xtra FGHR

Part number

Description

7 733 600 332

MT20 mechanical timer

7 733 600 333

MT20RF mechanical thermostat

7 738 110 054

Sense I

7 738 111 064

Sense II (including weather sensor)

1)

1) Preheat time control available.

7 738 112 324

II RF

7 738 112 338

stat RF

2)

2) Must be used with an external proprietary 230V timer.

Part number

Description

7 736 701 341

EasyControl (white)

1)

1) Preheat time control available.

7 736 701 392

EasyControl (black)

7 738 112 351

EasyControl RF Key

7 736 701 555

EasyControl TRV set (white)

7 736 701 556

EasyControl TRV set (black)

8 750 000 270

EasyConstrol smart TRV (individual)

Part number

Description

7 716 192 764

Outdoor weather sensor

«
...
9
10
11
12
13
...
»

Содержание GR2300iW C





































































































Отзывы:

Нет отзывов

Похожие инструкции для GR2300iW C

Бренд: Main Страницы: 12

Бренд: Magikitch'n Страницы: 4

Бренд: Ravenheat Страницы: 56

Calyadra comfort

Бренд: C&M Страницы: 12

Бренд: Prestige Страницы: 104

Бренд: Prestige Страницы: 114

Logano plus SB315

Бренд: Buderus Страницы: 16

Бренд: Baxi Страницы: 44

Solo WM 30/4 PF

Бренд: Baxi Страницы: 52

Бренд: SCHUSTER Страницы: 40

VICTRIX 24 TT 1E

Бренд: Immergas Страницы: 44

VICTRIX 12X TT 2 ERP

Бренд: Immergas Страницы: 48

Бренд: Immergas Страницы: 52

Бренд: EHC Страницы: 16

Бренд: Potterton Страницы: 56

Бренд: BENEKOV Страницы: 39

Бренд: Knight Страницы: 68

Бренд: THERMEx Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды