Worcester GR2300iW C Скачать руководство пользователя

Страница: 50 / 100

Commissioning

Greenstar 2000 – 6 721 820 552 (2021/02)

6.9

CO and combustion check

The following combustion and flue integrity checks are mandatory and
these values must be recorded on the Benchmark checklist, at the end of
these instructions.

Once the gas rate and pressure have been confirmed as acceptable then
the CO and combustion checks can be undertaken.

The flow chart is given for guidance, the details of the checks are given in
the following sections:

• Checking flue integrity, (



6.10 "Checking flue integrity")

• Flue gas analysis, (



6.11 "Flue gas analysis")

NOTICE

Before CO and combustion checks:

▶ Verify the appliance is connected to the correct gas type.
▶ Ensure the appliance is supplied with the correct gas inlet pressure

and gas rate as specified previously in the Commissioning section.

▶ Visually check the integrity of the whole flue system and confirm that

all the components are correctly assembled, fixed and supported.

▶ The flue gas analyser must be the correct type as specified in BS

7967. Before use the analyser must have been calibrated as
specified by the manufacturer. The installer must be competent in the
use of the analyser.

▶ Check and zero the analyser in fresh air as specified by the

manufacturer.

▶ The air/gas ratio valve is factory set and must not be adjusted during

commissioning unless this action is recommended following contact
with the Worcester, Bosch Group help line 0330 123 3366.

Fig. 66 Commissioning checks flow chart

Yes

Set boiler to

minimum rate.

Check all seals around the
burner, internal flue seals,

and case seals.

Rectify where necessary.

Turn off boiler and

call Worcester, Bosch

Group help line.

0330 123 3366

Boiler is operating

satisfactorily.

No further action

is required.

Verify flue integrity

≥ 20.6%

< 0.2%

≥ 20.6%

< 0.2%

Yes

Check CO and

combustion ratio

at maximum rate

Check CO and combustion

ratio at minimum rate

CO < 350ppm

CO/CO

ratio

< 0.004

CO < 350ppm

CO/CO

ratio

< 0.004

CO < 350ppm

CO/CO

ratio

< 0.004

Flue integrity test

using analyser

Yes

Set boiler to

maximum rate.

START

HERE

0010023581-002

Zero the analyser

in fresh air.

See notice above

Record values.

Do not adjust
the gas valve.

≥

= greater than

or equal to

= less than

Содержание GR2300iW C





































































































Результаты поиска

Содержание GR2300iW C

Отзывы:

Похожие инструкции для GR2300iW C

Бренды по названию

Популярные бренды

Worcester GR2300iW C, Инструкция по установке и обслуживанию

Результаты поиска

Содержание GR2300iW C

Отзывы:

Похожие инструкции для GR2300iW C

Бренды по названию

Популярные бренды