Woodward 2301E-ST Скачать руководство пользователя страница 74

Страница: 74 / 126

Manual 26694

2301E-ST

Woodward

16 NETWORK ADDRESS

dflt=1 (1, 247)

Set the Network Address input defines the slave block address on the Modbus network. The network
address may depend on master device allowable addresses.

17 ENABLE MODBUS CONTROL

dflt=FALSE (FALSE, TRUE)

When set TRUE you are able to control using Modbus.

U** APPLICATION INFO **

Figure 3-32. Service: U** APPLICATION INFO ** Menu

This section shows the application software information.

01 APP Software Number

indicates the software part number.

02 APP Software Revision

indicates the status of the application software revision.

03 Application Name

indicates the application name.

04 SUPPLY VOLTAGE DC

Shows the power supply voltage level.

05 HARDWARE P/N

Indicates the hardware part number

06 HARDWARE S/N

Indicates the hardware series number

V** COMM PORT (MODBUS) **

Figure 3-33. Service: V** COMM PORT (MODBUS) ** Menu

The menu is used to setup the serial port for MODBUS use.

01 PORT FAIL

indicates a hardware fault of RS-422 communication port.

Released

Содержание 2301E-ST































































































































Результаты поиска

Содержание 2301E-ST

Отзывы:

Бренды по названию

Популярные бренды

Woodward 2301E-ST, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 2301E-ST

Отзывы:

Бренды по названию

Популярные бренды