Woodward 2301E-ST Скачать руководство пользователя страница 50

Страница: 50 / 126

Manual 26694

2301E-ST

Woodward

06 ANALOG INPUT #1 FAIL (4)

displays the status of Analog Input #1 (if configured). A failed input is detected

when the analog #1 exceeds the following ranges:

Input Set For:

Low Trip Point

High Trip Point

4–20 mA

2.0 mA

22.0 mA

0–5 Vdc

–0.63 Vdc

5.63 Vdc

±2.5 Vdc

–3.13 Vdc

+3.13 Vdc

1–5 Vdc

0.5 Vdc

5.5 Vdc

07 ANALOG INPUT #2 FAIL (5)

displays the status of Analog Input #2 (if configured). A failed input is detected

when the analog #2 exceeds the following ranges:

Input Set For:

<Low Trip Point

>High Trip Point

4–20 mA

2.0 mA

22.0 mA

0–5 Vdc

–0.63 Vdc

5.63 Vdc

±2.5 Vdc

–3.13 Vdc

+3.13 Vdc

1–5 Vdc

0.5 Vdc

5.5 Vdc

08 MODBUS ISSUED TRIP (6)

displays the status of the Modbus Issued Trip (if configured). A trip is

detected when an input from the Modbus controller has issued a trip command.

09 TEST MODE (7)

displays the status of Test Mode input. A trip is detected when the Actuator

Calibration or the Enable Hardware Test is enabled.

10 EXTERNAL SHUTDOWN (8)

displays the status of SHUTDOWN / RUN DISCRETE input. A shutdown is

detected when the discrete input on terminal 34 is FALSE.

11 STUCK IN CRITICAL (9)

displays the status of a shutdown caused by a stuck in critical band failure.

12 SHUTDOWN ACKNOWLEDGE

dflt=FALSE (FALSE, TRUE)

When set to TRUE will reset the SHUTDOWN RELAY discrete output. (See also description of RESET CLEARS TRIPS
in the configure menu C**DISCRETE OUT OPTIONS**.

D** ALARMS **

Figure 3-12. Service: D** ALARM ** Menu

This menu displays the status of the alarm modes.

01 ALARM STATUS

gives the existing alarm conditions. If control has alarms, it displays TRUE. If no

alarms exist, it displays FALSE.

Released

Содержание 2301E-ST































































































































Результаты поиска

Содержание 2301E-ST

Отзывы:

Бренды по названию

Популярные бренды

Woodward 2301E-ST, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 2301E-ST

Отзывы:

Бренды по названию

Популярные бренды