Wolf Garten Robo Scooter 500, Оригинальная инструкция по эксплуатации

Страница: 53 / 138

53 en
Splice wire (Con-
firm the Base Stati-
on beeps
continuously for
cut wire)
• Perimeter wire cut
• Wire disconnected from the Base Station / Perimeter
Switch
• Confirm wire is plugged in and wire leads are firmly at-
tached.
• Walk along perimeter, including islands and look for obvious
cuts or break in the wire. Repair with Robo Scooter 500 wire
splice connectors.
• In case the wire cut is not visible call your service dealer for
more information how to find the wire cut.
Start elsewhere
• An unknown fault has occurred and user help is requi-
red.
• Manually drive/carry the mower away from this particular
area and restart operation.
• Drive wheel motors have been working under a severe
load during automatic or manual operation.
• Check to insure the mower is not stuck, allowing the drive
wheels to slip.
• Check the ground for holes or indentions, where the mower
has stopped and fill it with dirt and level off.
• Check the drive wheels are free to rotate and nothing block
them.
• Remove the mower away from this particular point and re-
start operation.
Start inside
• Automatic operation is initiated while Robo Scooter
500 is placed out of the perimeter wire lope
• Place the mower inside the lawn and press the ‘GO’ button.
Stuck in place
• Robo Scooter 500 get stuck in place with no succeed
to continue driving.
• Check the ground for holes or indentions, where the mower
has stopped and fill it with dirt and level off – especially in the
area close to the perimeter, where the Robomow turns in
place.
• Robo Scooter 500 has difficulty to turn in place be-
cause the front wheel has fallen into hole or indention
and it caused the mower to turn in place without detec-
ting wire or bumper.
• Confirm the area is not too sloppy and make sure to work in
dry condition.
• Check the perimeter wire is not too close to the edge – re-
move if required.
• Conform the mowing deck is not set too low.
• There is an option to drive back to the lawn in reverse before
Robo Scooter 500 perform the turn in place (contact your
service dealer for details).
Switch off before
lifting • The user carries Robo Scooter 500 manually while the
main switch button is on.
• Switch off the main switch button before carrying Robo
Scooter 500.
Switch off before
lifting (While Robo
Scooter 500 is in
the Base Station)
• Robo Scooter 500 does not detect the power from the
base Station, there is a charging problem .
• Check the connection of the Base Station board cables (red
and black) to the Base Station pins; confirm the screws are
tightened.
• Confirm good contact between Robo Scooter 500 and the
Base Station charging pins.
• Make sure the pins are clean and not corroded.
Time and date
• Displayed every time the batteries fuse is taken out of
the mower (reset operation).
• Set real time clock (day and hour) and the date.
Time completed
• The operating time set for that zone has been
reached.
• Connect to the charger if all mowing has been completed for
the day.
Waiting for
signal… • Robo Scooter 500 has stopped the operation, be-
cause there is no signal detected.
• Check the power to the Base Station.
• There is electrical power interruption. There is no need to do
anything – Robo Scooter 500 will renew automatically the
operation if the power will come back within an hour from the
break; if the power will come back after more than one hour,
Robo Scooter 500 will drive back to the Base Station for
charging, but will not renew the operation and mowing.
Message
Displayed
Probable Cause/Event Corrective/User Action