Wolf Garten Robo Scooter 500, Оригинальная инструкция по эксплуатации

Страница: 43 / 138

43 en
Program type
Set by area
Define the area size of the zone connected to the Base Station and
the start time, at which you wish Robo Scooter 500 to start mowing;
Robo Scooter 500 will determine the most efficient weekly program to
your lawn based on the area given.
When setting weekly program by area, the active days will be as
shown in the table below.
Set by days
Select the days in which you wish Robomow to operate. Define the
start time and the work time, which are common to all active days.
3
Notes
z
The cursor indicates the day to be set.
z
‘+’is for active day.
Display program
3
Note
To display the program, press the ‘UP’ arrow while Robomow
is in the Base Station. The program is displayed for 10 se-
conds before changing back to the main display. To update the
program, press the ‘GO’ button within the 10 seconds that the
program is displayed.
The following characters may appear under each of the active days:
1. Press ‘GO’
2. Scroll ‘UP’to choose the lawn area
connected to the Base Station
3. Press ‘GO’
4. Scroll to set the start time and press
‘GO’to confirm (the ‘Start time’is the
same for all days)
Area m² Mon Tue Wed Thu Fri Sat Sun
0-50 x x
50-100 x x
100-150 x x x
150-200
x x x x
200-250 x x x x x
250-300 x x x x x x
300-
x x x x x x x
1. Use the UP/DOWN arrows to change
the day status.
2. Press ‘GO’to move to the next day.
3. Press ‘GO’to confirm.
4. Scroll to set the start time (the ‘Start
time’is the same for all days).
5. Press ‘GO’to confirm.
6. Scroll UP/DOWN to set the work
time.
7. Press ‘GO’to confirm.
Base zone area
Presse GO
150 - 200 m²
Confirm
200 - 250 m²
Confirm
Start: 14:00
Confirm
M+T-M-T-F-S-S
Next day
M+T-M-T-F-S-S
Confirm
Start: 13:00
Next digit
Start: 14:00
Confirm
Zone:Dock 1:30
Confirm
The weekly program display (figure 2.5) is
used to show additional information about
the last week operations except of the ‘+’
for the active days.
Character Meaning
+ Active day
B
Skipped due to low battery voltage; (Robo Scooter 500
did not depart from the Base Station at the scheduled
time due to low battery voltage)
b
Docked before time due to low battery voltage; (Robo
Scooter 500 did not complete the operation and drove
back to the Base Station due to low battery voltage –
relevant only when ‘Work time’ different from ‘Max’ is
set)
d
Robo Scooter 500 did not return to the Base Station
because of Drive over current ('Start elsewhere') or
'Drive problem'; Robo Scooter 500 returned to the
Base Station before time due to drive overheat.
M
Skipped due to mow over current detected in the Base
Station before Robo Scooter 500 has started the ope-
ration.
m
Robo Scooter 500 returned to the Base Station before
time due to mow problem (over current or over heat).
O
Skipped because the mower was out of the Base Sta-
tion at the scheduled start time.
P
Skipped due to power problem (there is no charging
voltage at departure time).
R
Skipped due to rain; (Robo Scooter 500 did not depart
from the Base Station at the scheduled time due to rain
detection)
r
Docked before time due to rain; (Robo Scooter 500 did
not complete the operation and drove back to the Base
Station due to rain detection during the operation)
S
Skipped due to signal problem (it may happened be-
cause of problem with wire sensors, cut perimeter wire,
poor splicing of perimeter wire or perimeter wire which
was too long).
s
Robo Scooter 500 returned to the base because of no
signal for more than 1 hr
U
Skipped due to user choice/interference (usually when
the ‘Program’ set to ‘off’)
u
Robo Scooter 500 did not return automatically to the
Base Station because of user interference
M T M T F S S
R + + + m - -