Wolf Garten Robo Scooter 500, Оригинальная инструкция по эксплуатации

Страница: 52 / 138

52
en
Key pressed
• One of the operating panel buttons is constantly
pressed.
• Press ‘GO’ to confirm the message and to continue in ope-
ration. The message is displayed to inform the user about
the problem, but will not prevent the operation.
Keys locked • Child lock feature has been activated
• Press the Up ? arrow key and then press the ‘STOP’ button.
Child lock can be deactivated under the ‘Settings’ menu.
Low battery
• Mower is searching for the Base Station but the batte-
ry voltage is too low to continue the searching pro-
cess.
• Drive the mower manually using the remote control or carry
it by hand for charging in the Base Station.
• Robo Scooter 500 has skipped the last start time due
to low battery voltage
• Confirm there is enough time between the two adjacent de-
partures so the battery can be charged prior the scheduled
operation (min 16 hours between operations).
Low temperature
waiting…
• Robo Scooter 500 is charged through the Base Stati-
on and the ambience temperature is out of range
(below 32ºF / 0ºC);
• Do not do anything, the charging is stopped and Robomow
is waiting for temperature to change back to the allowed ran-
ge; if temperature stays out of the range for more than 12
hours, the message is changed to ‘Low temp. Press GO’.
Mow overheat
cooling, wait… • The mowing motor has been working under a severe
load for too long of a time.
• There is no need to do anything – Robomow will renew au-
tomatically the operation, as the mowing motor will cool
down.
No wire signal
• Base Station / Perimeter Switch is not turned on or not
connected to the zone intended to mow.
• The perimeter wire is not connected to the Base Stati-
on / Perimeter Switch
• The perimeter wire is cut
• Make sure the Base Station is connected to the mains sup-
ply
• Disconnect the Base Station power supply from the mains
power and reconnect after 10 seconds.
• Check the Perimeter Switch is connected to the correct zone
and is turned on.
• Check the connection of the perimeter wire to the Base Sta-
tion / Perimeter Switch.
• Check for cut in the perimeter wire.
Peg base then
press GO • This message is displayed after ‘Base position’ test is
completed successfully.
• Fasten the base in place using the 2 stakes.
Rain detected GO
to ignore
• Robo Scooter 500 detects rain upon GO pressing (re-
ceived when pressing the GO button).
• Do not operate Robo Scooter 500 in rainy weather and wet
grass; If you choose to override, press the ‘GO’ button; The
overriding is valid for the current operation only.
• Robo Scooter 500 has skipped the last depart due to
rain detection.
• It is not recommended to cut wet or damp grass, but if you
choose to override the rain sensor, change the setting of the
‘Rain sensor’ to ‘off’ under the ‘Settings’ menu.
Rain sensor dis-
connected
• Disconnection in the rain sensor wires. • Press ‘GO’ to confirm
Ready keep char-
ging
• The battery is fully charged (displayed when charging
through the standard power supply and not through
the Base Station) • Keep the charger (power supply) connected and operating
Recharge battery
• The maximum operating time has been reached (dis-
played in non-Base Station zone)
• Connect the charger to the mower
Remove fuse befo-
re lifting • Robomow was lifted while the battery fuse is connec-
ted.
1
Warning!
Remove the fuse before lifting Robo Scooter 500.
Remove fuse then
check blade
• Some obstacle is stuck or wrapped around the blade.
• Something is preventing a blade from rotating freely.
Severe grass accumulation under the mowing deck;
rope or similar object wrapped around mowing blade.
• Object jammed under mower preventing blade from
rotating.
1
Warning!
Remove the fuse before lifting Robo Scooter 500.
• Inspect blades for foreign material or debris preventing rota-
tion.
• Clean out accumulated grass clippings using a wooden
stick.
Reposition base
• Robo Scooter 500 fails to enter the Base Station du-
ring ‘Base position’ test
• Reposition the Base Station; usually it should be placed with
the marked lines on the Base aligned with the perimeter wi-
re. If the Base is placed in narrow pass, where the distance
from the adjacent wire is less than 3 meters, the Base Stati-
on should be placed in shift of few cm towards out of the
lawn.
Message
Displayed
Probable Cause/Event Corrective/User Action