36
www
.wittur
.com
© WI
TTUR • All rights r
eser
ved
PM.2.004921.EN - 808-001-000 SDS
©
rel 3 · Edition 22 July 2020
Drive - Instruction Manual
8.3 SELF-LEARNING CYCLE ACTIVATION BY MEANS OF THE HANDSET
By using the handset to operate a self-learning cycle, interferences with possible signals coming from the main lift controller are avoided
•
Power the system
•
Turn “on” the door controller; if there are any closing or opening signals from the main lift controller, the operator will perform the
relevant reset cycle in low speed up to the end run limit
•
Connect the handset to RJ45 connector
•
If necessary, using keys
ã
and
ä
choose the required language and confirm with the “OK” key
•
Using keys
ã
and
ä
run through the MAIN MENU and choose "DOOR CONFIGURATION" , using the “OK” key confirm the option.
•
Then choose “SELF LEARNING” and press "OK"
•
If the operator is not on a closing position use key F2 (><) to allow the door to complete a closing cycle in low speed
•
Once the closure has been made, push again key F2 (<>) to allow a complete opening cycle in low speed
During this operation please check carefully that the operator completes its total expected travel.
At the end of the opening cycle the self-learning cycle is completed.
This will be signalled with the information “Self-learning completed”.
The following will be requested: “Guided Profile setting?”
•
Press the “OK” key to choose the option “Fast settings”
•
Press key F1 (EXIT) to restore the “main menu”
8.4 REVERSING SYSTEM FORCE SETTING BY MEANS OF THE HANDSET
•
Connect the handset to RJ45 connector
•
If necessary, using keys
ã
and
ä
choose the required language and confirm with the “OK” key
•
Using keys
ã
and
ä
run through the MAIN MENU and choose "advanced settings". Press the “OK” key to confirm the option.
•
Then choose REVERSING SYSTEM and press the “OK” key to confirm the option.
•
On the display the following options are viewed:
−
PC00 REVERS. SYSTEM CHOICE
−
PC34 IM SIGNAL TYPE
−
PC42 FSET SELF TUNING
−
PC09 REVERS. FORCE SETTING
−
REVERS. OFFSET SETTINGS
•
Using the keys
ã
and
ä
scroll through the REVERSING menu and select the option “REVERSING SYSTEM FORCE SETTING”
•
Press “OK” to confirm the choice;
On the left display side three values are shown selectable with
ã
and
ä
keys: the maximum value (MAX), the set value (SET) and the
minimum value (MIN).
It is possible to change those values with
á
and
â
.
On the right display side a graph is shown with the set force percentage regarding the maximum force.
•
Using keys
á
and
â
the viewed value is respectively decreased or increased;
•
Press key F2 (<> - ><) to check the door operation with the set reversing force value
•
Press key F3 (Menu) to restore the MAIN MENU
•
Press key F1 (BACK) to restore the menu ADVANCED SETTINGS;
8.5 OPTION “RESET SPEED PROFILE”
Choose this option to reset the movement parameter to the factory default values.
•
Connect the handset to RJ45 connector
•
If necessary, using keys
ã
and
ä
choose the required language and confirm with the “OK” ke
•
Using keys
ã
and
ä
run through the MAIN MENU and choose MAINTENANCE;
•
Press the “OK” key to confirm the option.
•
On the display the following options are viewed:
−
MONITOR
−
MLC MONITOR
−
RESET SPEED PROFILE
−
LAST ALARMS
−
ALARMS COUNTERS
−
DATA DOWNLOAD
−
DATA UPLOAD
−
STATISTICS
−
SOFTWARE UPGRADES
•
Using keys
ã
and
ä
run through the menu “MAINTENANCE” and choose the option “Reset speed profile”.
•
Using the “OK” key, confirm the option
8.6 OPTION “ADVANCED SETTINGS”
•
Connect the handset to RJ45 connector
•
If necessary, using keys
ã
and
ä
choose the required language and confirm with the “OK” key
•
Using keys
ã
and
ä
run through the MAIN MENU and choose ADVANCED SETTINGS;
•
After confirming the choice by pressing the “OK” key, a 5-code password is required on the display. The factory default access code is
00001.
Use keys
á
and
â
to move to different digits and to select the necessary coded digit use keys
ã
and
ä
; Press OK at the end.
